Rock and stone chimney repair in Sandalwood
Loose stones or open joints on your Sandalwood chimney? Local masons find out if it is full stone or veneer, free.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local stone masons who match mortar and joints in Sandalwood
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Every stone chimney in Sandalwood is identified as full stone or veneer before we price anything.
- Free inspection and estimateWhether your Sandalwood chimney is full stone or veneer is settled on a free visit, before any price.
- Upfront pricing, no hidden feesStones, joints and veneer area are priced in writing one line at a time.
- Family owned and operatedOur family-owned masons approve the mortar sample with you before the first joint is filled.
Gray cement smeared over old joints
A quick patch on a stone chimney can mean gray cement spread across the joints and onto the stone faces. Hard cement over soft stone can force movement and moisture through the stone instead of the joint, and it hides whether the mortar behind it has failed. It can also crack away from the stone, letting water in behind it.
We cut out old cement patches on chimneys in Sandalwood with care for the stone edges, then repoint with a mortar matched to the stone's hardness. The estimate shows how much has to come out before new mortar goes in.
Within Jacksonville city limits, Sandalwood is its own named neighborhood. Sandalwood falls within Duval County.
Stone chimney repairs we handle in Sandalwood
- Loose stones reset on fresh mortar beds
- Deep stone joints raked and repointed in layers
- Water barrier and lath repaired behind veneer
- Veneer cut back from the roof surface
How our masons repair a stone chimney in Sandalwood
-
Describe what moved
Tell us what has shifted or fallen, and the free visit comes equipped for it.
-
Build and backing confirmed
Corners, joints and the base show the build, and a loose piece shows what is behind the veneer.
-
Reset, repoint or reinstall
Stones go back on fresh beds, joints fill in layers, and veneer returns to a repaired backing.
-
Matched and cured
An approved mortar sample and the old joint profile guide the finish, and the cure time is written down.
Metal behind veneer inland in Sandalwood
Lath and ties behind veneer in inland Sandalwood are not fighting salt air. Rust still forms wherever water lingers behind the stone, which is why drainage matters as much here as anywhere.
When we find rust, we trace the water that caused it before resetting the stone.
10% off any service booked within 72 hours of inspection
Repointing, resetting or a barrier repair behind the face, each is discounted.
Four ways a stone chimney is built
Full stone chimneys are laid in mortar course by course, and the stone carries the weight. Anchored stone veneer is a facing of full stones tied back to the chimney behind it with metal ties. Adhered veneer is a thin facing, natural or manufactured, held by mortar alone to a backing of lath over a water barrier, or set straight onto bare masonry.
Natural stone sawn thin for veneer goes up the way manufactured veneer does, and its failures look the same. Each of the four has its own repair, which is why identifying the build is the first line on every stone estimate we write. Some chimneys mix builds, with full stone below the roof line and veneer above it, and each part is priced by its own method.
Telling full stone from veneer
Corners give the build away. Full stone turns the corner with whole stones that show their depth on both faces, while veneer corners use L-shaped pieces or cut returns. Joint depth helps too: full stone joints run deep into the wall, and adhered veneer has only a thin setting bed behind each piece.
At the base, adhered veneer should end at a screed or flashing with a small gap above the ground or paving. A loose piece, where there is one, shows the backing directly. We write down what told us the answer, not only the answer. Sound helps as well: tapping adhered veneer over a gap in its bond gives a hollow note that full stone does not.
Matching mortar strength to the stone
Repointing mortar should be no harder than the stone around it. When mortar is stronger and less permeable than the stone, stress and moisture move through the stone instead of the joint, and the stone edges crack or flake. Dense, hard stone tolerates a stronger mix, while soft, porous stone needs a weaker one.
We identify the stone before choosing the mix, using ASTM C270 mortar types as the starting point and adjusting for softer stone. The mix goes on the ticket so any later repair uses the same thing. Where an earlier repair used a harder mortar than the stone can live with, those joints are cut out and redone rather than matched.
What we check on a stone chimney in Sandalwood
- Water barrier and lath repaired before veneer is reset
- Base drainage exit checked and opened where buried
- Old cement patches and caulk cut out before repointing
- Crown and flashing findings priced as separate lines
Before a stone is taken out
Why not just seal the joints with caulk?
Caulk keeps water in as well as out, so the mortar behind it stays wet and fails. Repointing with the right mortar lets the joint dry the way it should.
Do you repair manufactured stone veneer as well as natural stone?
Yes. Manufactured veneer follows its maker's installation guide for the backing and setting mortar, and we match the product line and color as closely as it allows.
More services in Sandalwood
-
-
-
-
-
-
Learn more about stone chimney repairAll services in Sandalwood
Build first, then the joints
Our family-owned masons repair stone chimneys in Sandalwood and guarantee the work to your 100% satisfaction.
Free Inspection