Family-run gas fireplace venting in Switzerland

Caps too close to windows, decks or corners in Switzerland moved to meet the clearances, with the new route drawn out first.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local vent specialists who repair with listed parts

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Every repair ends with a test run while we watch the flame.

Free inspection and estimateThe vent on your Switzerland gas fireplace is traced from the collar to the cap and measured against the code at no charge.
Upfront pricing, no hidden feesEach section, fitting and reroute is priced on its own line before any pipe is cut or replaced.
100% satisfaction guaranteedIf the flame, the draft or the shutdown problem is not fixed by the vent repair we quoted, we come back.

Call (904) 920-5495 Free Inspection

A fireplace that spills when fans run

Room-air gas fireplaces can be overpowered by a strong kitchen hood or bath fan, which reverses the pull. Exhaust then pours out at the draft hood rather than rising. Opening a window during the test often shows how much the fans are pulling.

A smoke test with the fans on and off shows it, and units fitted with a spill switch should shut the gas off when it happens. Gas fireplace that acts up when the range hood runs in Switzerland? Call (904) 920-5495.

Switzerland lies within St. Johns County. Switzerland sits away from the coastline.

What gas fireplace venting covers in Switzerland

Insulation cleared from vent air spaces
Decorative shrouds checked over gas caps
A flame check after every repair in Switzerland
Roof covering work named for a roofer

Call (904) 920-5495 Free Inspection

From collar to cap in Switzerland

Identify the system
The manual and pipe markings tell us the vent type, size and maker.
Trace the run
With the unit off and cool, we follow the vent and check joints, supports and clearances.
Repair with listed parts
Joints are reseated, damaged sections replaced and crowded caps moved.
Test and record
We fire the unit, check flame and draft, then note every fix.

Nests in an inland termination

A wall termination in Switzerland is an inviting spot for wasps and birds. A nest in the cap starves the flame.

We clear it and check the screen and guard.

10% off any service booked within 72 hours of inspection

Cap too close to a window in Switzerland? The reroute is discounted too.

Call (904) 920-5495 Free Inspection

Elbows, offsets and the total bend

Every elbow in a vent adds resistance. One maker's direct-vent manual caps the total angular change in a system at 270 degrees and limits how far the pipe may run sideways after an elbow placed right on top of the fireplace to 36 inches.

Its B-vent manual allows at most two 90-degree elbows or four 45-degree elbows per installation, counting two 45s as one 90. When we repair or reroute a vent, the elbows are counted against those limits before anything is added, and a route that would exceed them is redrawn. Every elbow also adds a joint that has to stay tight.

Vent restrictors and when they are set

Restrictors balance exhaust and intake air on certain direct-vent layouts. One maker's manual calls for an open-center restrictor on its top-vent installations that use a 90-degree elbow and a vertical rise, made by breaking out the center of the supplied part.

A restrictor in the wrong position or missing where the manual calls for one changes the flame. After any change to a direct-vent run, we check the restrictor against the manual for the new layout and note its setting on the ticket. A restrictor removed during an earlier repair is a common thing to find.

When the pilot and burner go out

Losing the flame mid-run can point to the vent on a direct-vent fireplace. One maker's troubleshooting chart lists an inner vent pipe leaking exhaust back into the system, a horizontal vent pitched wrong, and a vent cap installed wrong or blocked.

The first calls for finding and replacing the leaking section, the second for rehanging the run with the right rise, the third for clearing or refitting the cap. We check all three before replacing any control part, since a new valve will not fix a vent that feeds exhaust into the intake. Each check is quick compared with the cost of a valve.

Clearances, slope and caps on paper

Elbows counted against the system's limits
Restrictor position checked against the manual
Spillage test at the draft hood with fans on and off
Roof covering work named for a roofer

Gas fireplace vent questions from Switzerland

Do you fix the roof around the vent?

The vent parts, collar and cap are ours; the roof covering is a roofer's work. The estimate names who does each.

What if I smell exhaust right now?

Turn the unit off and get fresh air. If an alarm sounds or anyone feels ill, leave and call 911 from outside, then call us at (904) 920-5495 for the Switzerland visit.