Local gas fireplace installation for Yulee homes
Natural gas or propane, a free visit plans the Yulee install, which ends with pressures read, connections leak-checked and the barrier fitted.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local gas fireplace experts for new installs in Yulee
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Every clearance comes from the unit's manual, from the header height to the mantel depth.
- Family owned and operatedOne family business frames, vents and starts up the unit in Yulee, and lines up the gas and electrical trades.
- Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.
How long a gas installation takes
Setting the unit in its framing is one of the shorter steps in the job. The calendar goes to the steps around it: the unit and vent parts arriving, framing the enclosure, running the vent, the gas contractor's line and any outlet, the inspection while the walls are open, and the finish. A wall exit is quicker to build than a roof exit, which adds attic work and roof covering. Your Yulee schedule shows the steps in order with who does each, so you know when the room is out of use and when it comes back. Picked a room for a gas fireplace in Yulee? (904) 920-5495 is the number for a free planning visit.
Yulee lies within Nassau County. At the 2020 Census, Yulee was home to 14,195 people.
What a gas fireplace installation covers in Yulee
- Wiring for the receiver and blower run before the wall closes
- Facing and mantel planned from the manual's chart
- Gas line to the shutoff valve assigned to a gas contractor
- Walk-through of your new Yulee unit and its manual
Vent out, frame, wire, start up
-
Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
-
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
-
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
-
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.
Wall openings in Yulee in the storm months
Hurricane season lasts from June through November. A new opening through the wall or roof has to be weathertight before any storm arrives.
Exterior work on installs in Yulee is timed to the forecast, and the opening is covered until the termination is sealed.
10% off any service booked within 72 hours of inspection
Settling on a model for a room in Yulee takes time, and the 72 hours give you some.
Reading the vent table
Each direct-vent manual we work from carries a vent table or chart that ties the vertical rise to the horizontal run. A unit that exits straight through the wall may allow only a short horizontal run; one that rises several feet first may allow a longer run after the rise. Each elbow counts against the total as a set length of straight pipe.
A route outside the table can pull too little air in or push exhaust back, so the burner misbehaves or the pilot drops. We draw the route, add up each length and elbow, and check the total against the table before cutting.
Above walks, drives and the ground
A termination has to sit high enough above the ground to stay clear of plants, debris and anything stacked against the wall, and the manual gives a minimum height above grade. Where the termination sits over a paved walkway or driveway between two houses, the clearance table drawn from NFPA 54 sets a much greater height, because people pass close to it. We check what is below the chosen spot, including walks, drives, steps and patios, and move the termination if the height cannot be met on that stretch of wall. Mulch beds that build up over the years reduce the height, so we leave some margin.
What the unit sits on
The manuals we install from let a unit sit directly on wood flooring or a subfloor. When it would sit on carpet, tile or another combustible surface other than wood flooring, the manuals call for a metal or wood panel under the full width and depth of the unit. The unit is then secured to the floor or to the framing with the fasteners and points the manual shows, so it cannot shift when the facing is installed or the glass is removed for service. Raised platforms are built to the same rule, with the panel on top. The panel goes on before the unit is slid into place.
Unit, vent route and trades on paper
- Horizontal pitch and support spacing set as the manual shows
- Termination spot measured to windows, soffits, corners and walks
- Noncombustible facing and mantel height checked against the charts
- Gas supply to the shutoff valve, named with the trade that runs it
Gas fireplace install questions from Yulee
Can I choose the tile or stone around the fireplace?
Yes, within the manual's rules. Only noncombustible materials may cover the metal face, set with the adhesive rating the manual gives, and a mantel follows the manual's chart.
Is a permit needed for a gas fireplace?
Yes. The permit comes from the local building department, and its inspections cover the gas connection, the vent and the framing before the finish closes them in. Both appear on the estimate.
More services in Yulee
-
-
-
-
-
-
Learn more about gas fireplace installationAll services in Yulee
Add a gas fireplace in Yulee
The unit, the vent route and the gas and electrical trades all appear on one written estimate for your install in Yulee.
Free Inspection