Local hearth tile and slab repair in Sandalwood

Tile lifting after water came down the flue? In Sandalwood, we stop the water first, then reset the hearth.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Hearth specialists who check the base first in Sandalwood

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

A small repair that will hold is priced as the small repair.

Free inspection and estimateYour hearth in Sandalwood is sounded, leveled and measured on a free visit before any price is written.
100% satisfaction guaranteedA tile or stone we set that comes loose is ours to fix, and we return to reset it.
Family owned and operatedA family-owned local crew explains each layer of the repair, from the support to the grout line.

Call (904) 920-5495 Free Inspection

Grout that crumbles while the tile holds

Cracked or missing grout on a hearth whose tiles are all solid is a finish repair. The joints get raked out and regrouted with a product suited to the heat near the opening and to the joint width. That is a smaller job than resetting tile, and the estimate should say so.

We sound every tile on your hearth in Sandalwood before calling it a grout job, because loose tile under new grout cracks the new grout. Local, family owned, and priced in writing before we start. Call (904) 920-5495.

Sandalwood does not reach the coast. Sandalwood is a neighborhood inside Jacksonville city limits.

Hearth repair work we take on in Sandalwood

Cracked hearth tile cut out and replaced
Stone slabs rebedded, glued or replaced
Loose brick on the hearth relaid in fresh mortar
Your hearth in Sandalwood measured and sketched before work

Call (904) 920-5495 Free Inspection

From the first tap to the first fire in Sandalwood

Describe the hearth on the call
Cracked, hollow, sunken or too small, a short description sets up the free visit and what we bring.
Sounding and measuring
Each tile is tapped, the slab's level is read and the extension is measured against the opening.
Support first, surface second
A moving slab or missing support is fixed before tile or stone goes back on a full bed of the named mortar.
Cured before heat, then handed back
The bed cures before grout and fire, and we show you the finished edge and where the clear zone ends.

Where the effort goes on a hearth in Sandalwood

With no coastal hardware to upgrade, a hearth repair in Sandalwood spends its effort on the parts that decide how long it lasts: the support, the setting bed and the heat strip at the front.

The estimate for your hearth in Sandalwood shows those three in order, so you can see where each part of the price comes from.

10% off any service booked within 72 hours of inspection

Tile, stone or slab, hearth repair in Sandalwood comes 10% off.

Call (904) 920-5495 Free Inspection

Setting a one-piece stone slab

A single stone slab spans its whole extension, so any void in its bed becomes a span. Granite, slate and marble all break when a heavy point load lands over a gap. Setting a slab means a full, even bed, with the slab lowered and pressed down so the mortar reaches its edges and corners.

Before a slab goes back, we check that the base is flat and sound, since a slab bedded onto a hump rocks on it. Heavy slabs take two or more people and a plan for lifting them without cracking them. That handling goes on the estimate too, because it is real work.

Cleaners that damage hearth stone

Marble, limestone and travertine are calcium-based stones, and acids dissolve them. Masonry cleaners and some tile cleaners are acidic, and a single wash can leave dull, etched patches. The Natural Stone Institute's care guidance points owners of these stones to neutral cleaners for that reason.

Soot on these stones comes off with neutral or alkaline methods and patience, and a deep stain may need a poultice. We identify the stone first and test any cleaner in a hidden corner. The method and the product go on the ticket so you can repeat what worked.

Sealing a natural stone hearth

Porous stone near a fire absorbs soot, ash and spills. A penetrating sealer slows that down without forming a film that could scorch or peel. The maker's data sheet sets the surface preparation, the dry time and how often it is reapplied.

Sealer goes on only after the repair has cured, and only on stone and grout that the product lists. Some dense stones take almost none. We note the product and the date on the ticket, so the next application follows the same data sheet instead of a guess, and the finish stays even across the old and new stone.

Tile, slab, support and size, in writing

Hearth and extension measured against the opening size and R1001.10
Support under the extension identified, from below where access allows
Seam at the firebox cleaned and refilled with a heat-suited material
Cure time before the first fire, written with the finish date

Hearth repair questions from Sandalwood

Is a same-day hearth visit possible in Sandalwood?

Same-day visits happen when a slot is open that day. Describe the hearth on the call and we give you the earliest time we have.

Will you match my stone or tile?

We look for the closest available match first and tell you plainly how close it is. If no match exists, we suggest a salvage spot or a deliberate contrast, and you choose before anything is removed.