Gas fireplace log replacement in Sandalwood

Vented logs with the damper clamped open, or vent-free logs where the room allows, installed in Sandalwood to the listing.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local gas log specialists who set logs to the manual

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Vent-free sets are recommended only where the room's size and use allow them.

Free inspection and estimateYour Sandalwood firebox, flue, damper and room are measured against the set's manual at no charge before anything is bought.
Upfront pricing, no hidden feesSet, burner, clamp, cleaning and any repairs are priced in writing, with the gas trade's part named.
100% satisfaction guaranteedIf the flame is sooty or the set will not stay lit after our installation to the manual, we come back.

Call (904) 920-5495 Free Inspection

Burning wood after gas logs go in

Once a gas log set is installed, the fireplace is for gas. A burner is not built to have wood burned on it, and one vent-free maker bans solid fuel in a fireplace fitted with its set. Dual-use plans shape which set and which clamp arrangement fit.

If you want the option of a wood fire now and then, that is part of the choice from the start. Want both wood and gas in one fireplace in Sandalwood? Ask what is possible at (904) 920-5495.

Sandalwood is an inland community. Sandalwood is one of the named neighborhoods of Jacksonville.

Gas log work for Sandalwood fireplaces

Vented log sets with permanent damper clamps
Cracked logs replaced from the set's parts list
Propane and natural gas sets matched to the plate
Room size worked out before vent-free logs go into homes in Sandalwood

Call (904) 920-5495 Free Inspection

How gas log installation runs

Measure firebox and room
Firebox, chimney height and, for vent-free sets, the room are checked against the manual.
Clean and clamp
Soot and debris come out of the fireplace, and vented sets get their permanent damper clamp.
Connect and test
Once gas reaches the valve, the set is connected, leak tested and its pressure read.
Place logs and light
Logs and embers go where the manual shows, and we light the set with you.

Heavy rain and a vented set in Sandalwood

Heavy storm rain reaches far inland between June and November, and water coming down an open flue lands on a vented set's burner.

A cap on the chimney keeps it out, and we check for one during the inspection.

10% off any service booked within 72 hours of inspection

Vented or vent-free logs, the install is discounted either way.

Call (904) 920-5495 Free Inspection

The oxygen sensing pilot on vent-free logs

Vent-free sets carry an oxygen depletion sensing pilot, which shuts the set off if the room's fresh air runs low. One maker's manual says the heater needs fresh air ventilation to run properly and points to its ventilation section if the set keeps shutting off.

Repeated shutoffs are a message about the room, not a nuisance to work around. We check the room volume, open connections and the house's tightness, and the sensing pilot is left exactly as the maker built it. The same maker notes that running above 4,500 feet of elevation can cause pilot outage. A shutoff after a long burn in a small room is the system doing its job.

Chimney height for a vented set

Vented logs rely on the chimney to carry their exhaust away, and one maker wants at least 15 feet of chimney between the hearth and the top for its vented burners.

Taller chimneys draw more strongly, which is why the same maker allows a smaller permanent damper opening as the chimney gets taller. We measure the height when we inspect the flue, and a chimney that falls short of the figure rules out that set, or calls for a different approach, before anything is ordered. The same table also accounts for factory-built fireplaces separately.

Protecting the valve during pressure tests

Gas piping gets pressure tested, and those tests can damage a log set's valve. One maker requires the appliance and its main valve to be disconnected from the supply piping during tests above half a pound per square inch, and isolated by closing its shutoff valve during tests at or below that.

When the gas trade tests a new line to the fireplace, we coordinate so the set is disconnected or isolated as the manual requires. It is a small step that saves a valve. A valve damaged by test pressure can leak or fail to regulate.

Measured in Sandalwood before a log set is ordered

Front lip or recess measured, with depth taken inside it
Chimney height from the hearth to the top for a vented set
Flue, damper and firebox cleaned and inspected before the burner goes in
Screen in place, with flames curling in and away from it

Before a log set goes in

Why are my gas logs getting sooty?

Flame touching a log it should not reach, a burner or ember bed out of order, or a shortage of air. Logs go back to the manual's layout and the burner and air get checked.

Can I convert my log set to propane?

It depends on the set. Some are not convertible in the field at all, and others convert with the maker's instructions. The rating plate and manual decide.