Chimney flue tile replacement in Northside
Clay liners, mortar and flue size handled the way the code sets them out, on Northside chimneys large and small.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Family-owned flue experts serving Northside
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Repair comes first when it will hold, and relining only when it will not.
- Free inspection and estimateThe flue at your Northside home is swept, examined from both ends and mapped at no charge.
- 100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
- Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.
Tiles disturbed by work at the top
Work at the chimney top can disturb the last tile. A cap clamped too hard, a crown chipped away or a tile knocked while other work was done can leave a crack where there was none.
A top tile is reachable, so this is often a small repair: the tile is replaced or its broken edge cut back, and the seal around it is remade. We check the tile below too, since a knock can travel. Top tile damaged after recent roof or cap work in Northside? Phone (904) 920-5495 for a free flue inspection.
Northside sits in Duval County. Northside sits away from the coastline.
Flue repairs we handle in Northside
- Cracked top tiles cut out and replaced from the roof
- Cracked and gapped sections coated with a listed resurfacing system
- Relining quoted plainly when repair will not hold
- Every defect written down by height
Sweep, map, repair, check
-
Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
-
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
-
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
-
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.
Flue size and draft in Northside
Draft problems after a repair usually come from a flue made too small. The code's size rules apply the same in every town.
In Northside we measure before resurfacing, so the repaired flue still draws for the fireplace it serves.
10% off any service booked within 72 hours of inspection
The 72 hours for flue work in Northside start at your own inspection.
Where the tile passes through the top
Section R1003.9.1 wants the concrete, metal or stone top of a masonry chimney to drip water clear and to meet each liner through a caulked joint. That caulked joint, the bond break, lets the tile move without cracking the concrete around it.
Once that joint fails, rain finds the gap and trickles along the outer face of the tile into the stack, and concrete cast tight against the tile can crack it as they move. On top-tile repairs, we cut the old seal out, check the tile's edge and reseal around it. A tile replaced without remaking that joint tends to crack again at the same place.
How we examine a flue without opening it
Nearly all of a flue is out of reach, so it is examined from its ends. From the roof, we look down with a strong light. From the firebox or cleanout, we look up with a light and mirrors. The tiles are counted from the top, so every defect can be placed by height.
Where a stretch of flue cannot be seen from either end, we say so in writing. We do not guess at a section we could not see, and the estimate notes whether more access is needed before that part can be judged. Knowing what was and was not seen is part of an honest flue report.
Tiles that have slipped out of line
Flue tiles are meant to be supported on all sides and stacked in line, one squarely on the next. When a tile slips, the joint above and below it opens and the inside of the flue develops a step.
A slipped tile cannot be pushed back from the top, and a coat over the step does not realign it. If the displaced sections are near the top, they can sometimes be replaced from the roof. Lower down, a slip usually means relining. We record the position and size of any step, since that fact drives the whole repair choice.
Flue findings written down before pricing
- Sweeping needed before the flue can be judged, listed on its own
- Dividers between neighboring flues checked where they can be seen
- Refractory mortar to ASTM C199 named for any tile reset
- Water entry at the cap and bond break priced alongside
Flue repair questions from Northside
Can my water heater flue be repaired the same way?
Sometimes, but gas appliance flues follow the code's fuel gas chapter and the appliance's own venting rules. We read the appliance plate first and choose a repair or liner that suits it.
When can I light a fire again once the flue is fixed?
After the mortar or resurfacing coat has cured for the time its maker specifies. The estimate gives that time, and we confirm the flue is clear before you light the first fire.
More services in Northside
-
-
-
-
-
-
Learn more about chimney flue repairAll services in Northside
Repair cracked flue tiles in Northside
Our flue pros sweep, map and price every defect in your Northside flue. Call (904) 920-5495.
Free Inspection