Local chimney rebuild in Lakeside

From roof protection to the first fire, your Lakeside chimney rebuild is planned step by step on a free inspection.

Family owned and operated
Free inspection and estimate
Same-day service available
Upfront pricing, no hidden fees

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

or call (904) 920-5495

Why Choose Us

Rebuild specialists who test every course in Lakeside

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off when you book today

A rebuild in Lakeside goes down only as far as the masonry is loose, and we show you where that line falls.

Family owned and operatedOur family business takes your Lakeside chimney down by hand and lays it back up itself.
Upfront pricing, no hidden feesThe take-down line, flue plan and crown are priced before the first brick comes off.
Workmanship warrantyFrom the new courses to the counterflashing, the rebuilt stack carries our workmanship warranty.

Call (904) 920-5495 Free Inspection

How a rebuild runs, day by day

The first day is protection and take-down: the roof covered around the stack, the fireplace sealed inside, and brick lowered by hand to the chosen line. Next comes the flue decision in practice, with tile set or space left for a liner, then the courses laid back up with flashing let in as they pass the roof.

The crown is cast last and left to cure before the cap goes on. Weather can stretch the middle days, and the Lakeside schedule shows which days need someone home. Mortar is mixed in small batches on the ground and carried up as needed. The take-down line for your Lakeside chimney is set on a free inspection; call (904) 920-5495.

Lakeside is part of Clay County. Lakeside had 31,275 residents at the 2020 Census.

What's Included

Rebuild work around Lakeside

Sound original brick cleaned and saved to relay
Mortar type chosen from ASTM C270 for the exposure
Counterflashing let into the new joints as the stack rises
Cap anchored once the crown has cured

Call (904) 920-5495 Free Inspection

How It Works

How a rebuild in Lakeside runs

Take-down line marked
We test each row of brick from the top down and mark where sound brick starts.
Old brick taken down by hand
The flue is covered and the roof protected, then brick comes off a row at a time, with sound brick saved to relay.
Relaid plumb around the flue
Brick goes back in matched mortar with tooled joints, around new clay tile or ready for a listed liner, and is flashed into the roof.
Crown cast, cap on last
A new crown with an overhang and a drip edge cures before the cap goes on and the first fire is lit.

Local Conditions

Counterflashing set as the stack rises in Lakeside

A rebuild passes the roof line course by course, which is the moment to set counterflashing into the bed joints or cut a clean reglet once the masonry cures.

On rebuilds in Lakeside, the counterflashing is part of the masonry work.

10% off your first service when you book today

A rebuild booked today for your Lakeside home comes with 10% off a first service.

Call (904) 920-5495 Free Inspection

Lowering brick from the roof

Brick comes off a chimney by hand and comes down under control. Pieces are passed to a bucket on a line or sent down an enclosed chute to a container on the ground. Nothing is tossed over the eave onto a roof or a bed below.

The mortar and brick fragments are kept separate from sound brick being saved for reuse. The work area on the roof is swept as it goes, since loose grit under a boot on sloped roofing is a fall risk and grinds into shingles. Nothing heavier than a bucket load travels at once, so the line and the roof edge are not overloaded.

Tooling the joints so water runs off

How a mortar joint is finished decides how it handles rain. The brick industry's water-penetration guidance favors concave and V-shaped joints, along with grapevine joints, because the tool presses the mortar tight against the brick and leaves a profile with no ledge for water to rest on.

Timing counts too. Joints are tooled when the mortar has firmed enough to hold a thumbprint without smearing, then brushed lightly. Joints tooled too early smear; too late, they crumble at the surface and leave pores for water to get in. In the rebuilt section, the profile is matched to the joints that stay wherever that profile sheds water.

Where new flue tile starts and how far it may lean

The code sets where clay tile begins. For a flue serving an appliance, it starts no less than 8 inches under the lowest inlet; for a fireplace, it starts at the top of the smoke chamber, and it runs to a point above the enclosing walls (FBC R1003.12).

The tile runs vertically where it can, and where it must offset, the slope stays within 30 degrees of vertical. A rebuild that goes low enough to reach the smoke chamber rebuilds that starting point too, and you know in advance how far down the new tile begins. The first tile sits on a solid base, clear of loose rubble.

Free Inspection

Tested before a rebuild is priced in Lakeside

Flue covered so brick and mortar chips stay out of the smoke chamber
Joint profile tooled concave or V once the mortar firms
Counterflashing let into new joints over the roof's step flashing
Cricket need for a wide chimney, and who builds it

FAQ

Before the first brick comes off

Will the rebuilt section look like the rest of the chimney?

Original brick is reused where it tests sound, and new brick is chosen for size, then color and texture. New mortar shades differently at first and settles as it cures. An exact match is not something anyone can promise; the estimate shows which brick is planned.

Will a roofer be involved in the rebuild?

Sometimes. The rebuild includes counterflashing set into the new joints, but base flashing woven into the roofing, a cricket, or roofing repairs may need a roofer; each is assigned on the estimate.

Our Services