Electric fireplace service in Fleming Island by local pros
Electric fireplaces in Fleming Island tested part by part and repaired with the maker's parts by local family pros, free inspection first.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local electric fireplace pros for Fleming Island homes
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Inserts and wall units are handled with the trim and wall protected.
- Free inspection and estimateYour Fleming Island unit is tested part by part, from the outlet to the board, at no charge.
- 100% satisfaction guaranteedIf the repaired unit does not heat, light and respond as its manual says, we return and put it right.
- Family owned and operatedThe family crew that traces the fault in your unit is the crew that repairs it.
A thermostat that will not hold
Set to a temperature, the heater should cycle on and off to hold it. If it runs flat out and never stops, or clicks on and off every few seconds, the thermostat or its sensor may be at fault. A thermostat sensor blocked by trim or furniture can misread the room too.
We check the setting, the sensor's position and the thermostat's response, then replace the failed part. A unit mounted where its sensor sees warm air from the heater itself can also misread the room, and that is a placement issue we can explain. Temperature control acting up in Fleming Island? Phone (904) 920-5495 for a free inspection.
The coastline lies beyond Fleming Island. Fleming Island lies on the St. Johns River.
Heater, flame, board and remote
- Heater elements tested and replaced
- Every function retested before we leave
- Your Fleming Island unit diagnosed for free before any part is ordered
- Parts for your Fleming Island fireplace matched to its serial number
How our repair pros fix an electric fireplace in Fleming Island
-
Model number first
Read us the rating label, and parts availability is checked before the visit.
-
Supply, then each part
The outlet and breaker are checked, then heater, fan, flame effect, board and remote are tested in order.
-
Failed part replaced
The maker's part for your serial number is fitted, with any electrician work done separately.
-
Retested with you
Heat, flames, remote and thermostat are run through their settings before we leave.
Hot plugs in Fleming Island homes
A heater's steady load can heat a worn outlet in any house, and that is electrician work.
We check the unit's cord and plug in Fleming Island once the outlet is repaired.
10% off any service booked within 72 hours of inspection
Fixing an electric fireplace at your Fleming Island home? The repair keeps our workmanship warranty with 10% off the price.
Fan motors, bearings and noise
The fan moves room air across the element and back out into the room. As its bearings wear, it slows, grinds or whines, and a slower fan lets the element run hotter, which can trip the cutoff.
We spin the fan by hand with the power off to feel for roughness, then run it to listen. Dust on the blades is cleaned off, since it throws them out of balance. A worn motor is replaced as a unit with the maker's part. The fan is then run long enough to confirm the noise has gone and the airflow is back. A fan that starts slowly on a cold day and then speeds up is also a sign of wear.
The flicker rod and its motor shaft
Many flame effects use a rod with reflective strips or ribbons that turns slowly in front of the light source. The turning breaks the light into moving patterns that look like flames. The rod is pushed onto the shaft of a small motor.
Dimplex notes the rod can slip off the motor shaft, and when it does, the flames freeze. Reseating it is a quick repair once the unit is open. We also check the rod's bushing at the other end and the rod itself for bends, since a bent rod wobbles and makes the flames stutter. Once reseated, the rod is watched through a few minutes of running to be sure it stays put.
Hot plugs and scorched outlets
Heaters draw a steady load, and a worn outlet or loose connection heats up under it. The signs are a plug that feels hot, brown marks around the slots or a faint smell of hot plastic.
The outlet and the wiring behind it are electrician work under NFPA 70. What we check is the unit side: the cord and plug for heat damage, which, if present, means replacing the cord set with the maker's part. The fireplace goes back into use only once the outlet has been repaired and the plug is sound. A cord set is never cut and spliced, since the replacement from the maker keeps the unit as it was listed.
What we test on units in Fleming Island
- Connectors inside the unit checked for fit and heat marks
- Repair total compared with a new unit where it gets close
- Parts used and tests done written on the invoice
- Old parts taken away and the area cleaned
Before a part is ordered
Why does my unit heat for a while and then stop?
Often the thermal cutoff is doing its job because the unit is running too hot inside, from a blocked intake, packed dust or crowded trim. We reset it, find the cause and fix that.
What does a repair visit in Fleming Island cost?
Diagnosis costs nothing, and you see the part and labor price before any order goes in. Approve the repair within 72 hours and 10% comes off it.
More services in Fleming Island
-
-
-
-
-
-
Learn more about electric fireplace repairAll services in Fleming Island
Heat and flames back, in Fleming Island
Cold air, dark flames or a dead remote in Fleming Island? The diagnosis is free, and a repair booked in the next 72 hours is 10% off.
Free Inspection