Chimney flue tile replacement in Arlington
Family-owned flue specialists map your Arlington flue from top to bottom for free, then save the liner where it can be saved.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Flue specialists who map before they repair
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The plan covers the whole flue, so separate fixes do not pile up over the years.
- Free inspection and estimateThe flue at your Arlington home is swept, examined from both ends and mapped at no charge.
- 100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
- Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.
A cleanout door at the base
Chimneys that vent an appliance usually have a cleanout near the base, a small metal door that gives access to the bottom of the flue. The code puts it within 6 inches of the base and asks for a noncombustible cover.
A rusted or missing door leaks air into the flue and lets debris spill out. It is also where the bottom of the flue can be seen during a repair. We check it on every flue job and price a new door when it no longer closes. Cleanout door missing on your chimney in Arlington? Call (904) 920-5495 and book a free inspection.
Jacksonville University can be found in Arlington. Arlington is a neighborhood within the City of Jacksonville.
Tile, joint, seal and size
- Flue swept, then examined from both ends
- Relining quoted plainly when repair will not hold
- Flue repair for fireplaces and appliance flues alike
- A written flue plan for your Arlington chimney, free of charge
Sweep, map, repair, check
-
Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
-
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
-
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
-
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.
Flues that were built with open joints in Arlington
Some flue gaps come from how the tiles were laid, with little mortar between them. That is a construction question, not a location one.
We find those joints in Arlington flues after sweeping and price the resurfacing or relining that closes them.
10% off any service booked within 72 hours of inspection
From one cracked tile to a full relining, flue work in Arlington is discounted.
Flues that bend and the 30 degree limit
Leaning is allowed in a flue lining, within a limit. The code allows a slope no greater than 30 degrees from vertical. Beyond that, gases slow, deposits settle and the bend becomes hard to clean.
At an offset, tiles are cut on an angle and the joints are awkward to fill, so cracks and gaps cluster there. Repairs at a bend have limits too. Tools for resurfacing must pass the angle, and a replacement tile must be cut to match it. We note each offset's position and angle on the flue map, since it decides which repair can reach the damage.
Why the flue is swept before it is judged
Soot and deposits cover cracks. A flue that has not been swept can look sound when it is not, and a crack can look like a stain. So the flue is cleaned before it is examined for repair, from the smoke chamber up to the last tile.
Once the tile surfaces are bare, cracks, open joints and flaking faces show clearly under a light. That is when the flue map is drawn. If sweeping is needed, it is listed on the estimate as its own item, because the repair cannot be judged or done over the deposits. Brushing also clears loose chips that would otherwise fall into a fresh coat.
Repairing a flue that serves a gas appliance
Flue linings for gas appliances fall under the code's fuel gas chapter, and gas appliance makers set their own venting rules. A clay flue that once served a fireplace is not automatically suited to a furnace or water heater.
When a flue serves a gas appliance, we read the appliance's rating plate and instructions before choosing a repair. Some appliances need a liner of a particular type and size, and a clay flue repaired to suit a fireplace can still be wrong for them. The appliance itself, including its connection and gas supply, stays with the gas contractor, and the estimate names who does what.
Flue findings written down before pricing
- Every defect located by flue, height and wall on a written flue map
- Offsets and bends noted with their height and angle
- Refractory mortar to ASTM C199 named for any tile reset
- Relining priced when repair cannot give a sound, sized flue
Flue repair questions from Arlington
How do you see inside a flue?
From both ends, with a strong light and mirrors, after the flue is swept. Anything we could not see is written down as not seen, so nothing is guessed.
Is flue repair cheaper than relining?
When the damage suits a repair, it is usually the smaller job. When it does not, stacking repairs on a failing flue costs more in the end, and we price relining instead so you can compare.
More services in Arlington
-
-
-
-
-
-
Learn more about chimney flue repairAll services in Arlington
Repair cracked flue tiles in Arlington
Our flue pros sweep, map and price every defect in your Arlington flue. Call (904) 920-5495.
Free Inspection