Chimney crown repair in Tallulah-North Shore by local masons

In Tallulah-North Shore, a failed mortar wash comes off down to sound brick and a real cast crown goes on, once a free inspection confirms it.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Crown repair specialists who seal or recast in Tallulah-North Shore

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Coatings go on only in the weather window the maker allows, so the seal has time to set.

Free inspection and estimateWe map the cracks on your Tallulah-North Shore crown and check the brick under it at no charge.
Upfront pricing, no hidden feesCoating and recasting are both priced on paper, so you see the difference before choosing.
100% satisfaction guaranteedIf the finished crown is not right, tell us and we come back to put it right.

Call (904) 920-5495 Free Inspection

No overhang, no drip

Crowns that stop flush with the brick, or short of it, send every drop of rain straight down the faces of the chimney. The top courses stay wet, the joints wash out, and brick faces start to flake. The code's drip edge requirement is aimed at exactly this.

An existing crown cannot be given an overhang by adding a coating or a skim. Where missing overhang is causing damage below the Tallulah-North Shore crown, the answer is recasting the top so it projects past every face, grooved underneath. The faces below get checked for the damage that runoff already did. Cracks on top of your Tallulah-North Shore chimney? Our masons inspect crowns for free, so call (904) 920-5495.

Tallulah-North Shore lies within Duval County. Tallulah-North Shore does not reach the coast.

Crown work from crack map to cure

Wider cracks filled before a crown coating goes on
Loose top courses relaid before the new crown is cast
Roof and gutters cleared of crown debris at your Tallulah-North Shore home
Coat or recast decision for your Tallulah-North Shore crown in writing

Call (904) 920-5495 Free Inspection

From crack map to cured crown in Tallulah-North Shore

Crack map from the roof
We identify the type of top and sketch each crack with its width, so the choice between coating and recasting is based on what is there.
Prep for coating or removal
A sound crown is cleaned and its wider cracks filled; a failed one is broken out down to sound brick.
Coat, or form and pour
The coating is brushed on in dry weather, or new concrete goes into forms with an overhang, a drip groove and reinforcement.
Cure, seal and refit the cap
The bond break at each flue is sealed, the concrete cures under cover, and the cap goes back on.

Coating a sound crown in Tallulah-North Shore

Many cracked crowns in Tallulah-North Shore are still solid underneath. When the slab does not move under pressure and the cracks are hairline, a flexible crown coating is the right repair and the smaller bill.

We fill the wider cracks first, tape the flue tiles and brush the coating on in a dry spell.

10% off any service booked within 72 hours of inspection

Seal or recast, crown repair in Tallulah-North Shore earns the 10% discount.

Call (904) 920-5495 Free Inspection

The drip groove under the overhang

Water running off the edge of a crown wants to curl back along the underside and run down the brick face. A drip groove, a small channel cast into the underside of the overhang, breaks that film of water so it drops clear of the chimney.

The groove sits near the outer edge of the overhang, and it has to run continuously around all four sides. A groove that stops short at a corner lets water find its way around the end. A drip edge is one of the crown requirements in R1003.9.1, and the groove is how a cast crown provides it.

A flashing sheet under the crown

The Brick Industry Association's details put a sheet of flashing directly under a cast crown, running past the inside of the brick and turned up against the flue tile. The flashing catches any water that gets through the crown and sends it out as a drip beyond the face.

Technical Note 19B highly recommends flashing under cast-in-place caps and notes that it can double as the bond break between crown and brick. We include it where the chimney's construction allows it, and we say whether your crown gets one and why. The flashing metal is chosen to sit in mortar without corroding.

Crowns around a stainless liner top plate

After a flue is relined with a stainless steel liner, a top plate sits on the crown and the liner passes through it. The plate is sealed to the crown so water cannot run down between the old flue tile and the new liner.

Repairing the crown on a relined chimney means taking that plate off, repairing or recasting the crown, and resealing the plate to the finished surface with a sealant rated for the job. The liner itself is left undisturbed. If the plate is corroded or the seal has failed repeatedly, that becomes a separate line.

Coat or recast, and the reasons

Removal of the failed top down to sound brick
Reinforcement and concrete mix for a cast crown
Flue tile height above the finished crown
Chimney cap removal and reinstallation, with how it is fastened

Crown repair questions from Tallulah-North Shore

Can a crown be repaired in the rain?

No. Coatings and fresh concrete both need dry conditions for a set time after they go on. Crown work is scheduled for dry weather, and rain protection is on hand in case a shower arrives early.

Can a drip edge be added to my existing crown?

Not in a way that lasts. A drip edge has to be formed into the underside of an overhang, and a crown without an overhang has nowhere to put one. The fix is a new crown formed wider than the chimney.