Chimney flue resurfacing and repair in Sunbeam
Cracked or gapped flue tiles in Sunbeam found by height and repaired by local family flue pros, after a free inspection.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Flue specialists who map before they repair
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Every flue is measured, so a repair does not shrink it below the size the code sets.
- Free inspection and estimateThe flue at your Sunbeam home is swept, examined from both ends and mapped at no charge.
- 100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
- Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.
Where the liner meets the smoke chamber
In a fireplace chimney, the clay lining is meant to start at the top of the smoke chamber. That joint, between the sloped chamber walls and the first tile, is a common place for gaps, because the transition is awkward to build.
A gap there lets hot gas reach the masonry at the bottom of the flue. We look at it from the firebox with a light and mirrors, and a repair to the first tile is priced separately from any smoke chamber work. Gap at the bottom of your Sunbeam flue? Call (904) 920-5495, and our flue team will check it free.
Within Jacksonville city limits, Sunbeam is its own named neighborhood. Sunbeam falls within Duval County.
Tile, joint, seal and size
- Loose mortar ridges knocked back inside the flue
- Relining quoted plainly when repair will not hold
- Flue repair for fireplaces and appliance flues alike
- Cure time respected before the first fire
How our flue pros repair a flue in Sunbeam
-
Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
-
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
-
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
-
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.
Rain through an uncapped flue in Sunbeam
Uncapped flues take rain straight down, inland or not. Soaked joints lose their mortar sooner than dry ones.
A cap priced with a flue repair in Sunbeam keeps the new work dry.
10% off any service booked within 72 hours of inspection
Flue repair earns the 10% off even if you have booked with us before.
Flues that bend and the 30 degree limit
Leaning is allowed in a flue lining, within a limit. The code allows a slope no greater than 30 degrees from vertical. Beyond that, gases slow, deposits settle and the bend becomes hard to clean.
At an offset, tiles are cut on an angle and the joints are awkward to fill, so cracks and gaps cluster there. Repairs at a bend have limits too. Tools for resurfacing must pass the angle, and a replacement tile must be cut to match it. We note each offset's position and angle on the flue map, since it decides which repair can reach the damage.
Flues that serve an appliance
For a flue connected to an appliance, the code sets a simpler floor: the flue is not to be smaller than the connector from the appliance (R1003.14). A flue shrunk by a repair below that size can spill gases at the appliance.
The code also points gas appliance flue linings to its fuel gas chapter, and the appliance's own instructions may set further limits. So before repairing a flue that serves a furnace or water heater, we read the appliance's rating plate and connector size. The repair method is chosen to keep the flue at or above what that appliance needs.
Heat cracks in clay tile
Clay tile tolerates steady heat better than sudden heat. When a very hot fire meets a cold flue, the inner face of the tile grows faster than the outer face, and the tile can split along its length.
These cracks tend to run vertically and can repeat in tile after tile along the hottest stretch of the flue. A single hairline split in an otherwise sound flue can be resurfaced. Several split tiles, or splits that have opened wide enough to move, point to relining. The flue map shows how many tiles are affected and how far up the damage runs.
What goes on the flue map in Sunbeam
- Resurfacing system named with its UL 1777 listing, where one is used
- Gaps at the smoke chamber and at the top end of the lining
- Relining priced when repair cannot give a sound, sized flue
- Water entry at the cap and bond break priced alongside
Before a flue repair is chosen
Does resurfacing make the flue smaller?
A little, because the coat adds thickness to every wall. We measure the flue and the fireplace opening first, and resurfacing is only offered when the flue will still meet the size the code asks for.
When can I light a fire again once the flue is fixed?
After the mortar or resurfacing coat has cured for the time its maker specifies. The estimate gives that time, and we confirm the flue is clear before you light the first fire.
More services in Sunbeam
-
-
-
-
-
-
A flue that carries the smoke out of your Sunbeam home
The same family crew that inspects your Sunbeam flue for free is the one that repairs it.
Free Inspection