Fireplace damper repair for Sunbeam fireplaces

New plates, new frames and new handles for Sunbeam fireplaces, priced upfront after a free look from below with a light.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Family-owned damper experts serving Sunbeam

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Replacement plates are matched to your frame by measurement, so they swing and seat properly.

Free inspection and estimateYour Sunbeam damper is run through its full travel and checked with a light at no charge.
100% satisfaction guaranteedIf the repaired damper does not open fully and close flat, we come back and make it right.
Family owned and operatedA family business does the diagnosis and the repair, so the person who quoted it answers for it.

Call (904) 920-5495 Free Inspection

A poker handle that will not hold

The poker damper is the simple kind. A rod with a handle hangs down in front of the firebox, and notches along it catch on a bracket to hold the plate open at set positions. When the notches wear smooth or the rod bends, the plate slides shut on its own weight.

A plate that drops closed during a fire is dangerous, so this is a repair to make before the next one. Sometimes the rod can be replaced alone. Sometimes the bracket or the plate lug has worn too, and the fix is bigger. Damper handle slipping in Sunbeam? Our local pros inspect it for free at (904) 920-5495.

The county for Sunbeam is Duval County. Sunbeam is inland.

What a damper visit covers in Sunbeam

Poker rods and notch brackets renewed
Cracked or rusted-out frames cut out and replaced
Top seal priced where a throat swap is impractical
Written options for your Sunbeam fireplace before any part is ordered

Call (904) 920-5495 Free Inspection

From the first light test to a sealed plate in Sunbeam

Handle and plate tested
With the fireplace cold, the control is worked through its travel and the plate checked from below with a light.
Failed part named
Pivots, plate, frame or control, the part that failed is written down with the repair options and prices.
Freed, rehung or replaced
Sound parts are cleaned and freed, a plate is matched to its frame, or a new damper is set at code height.
Travel and seal confirmed
The plate must open fully and close flat under the light before the job is done.

Dampers seized from disuse in Sunbeam

Away from the coast, one of the hardest things on a damper is simply sitting unused. Pivots rust in place over idle months and the plate stops moving.

Opening and closing the damper by hand a few times a season keeps a sound damper in your Sunbeam fireplace working.

10% off any service booked within 72 hours of inspection

Damper work booked within the 72 hours is discounted, and it does not have to be your first job.

Call (904) 920-5495 Free Inspection

Cutting out a rusted damper frame

When a damper frame has rusted into the masonry, it cannot simply be lifted out. The frame is set in mortar at the top of the firebox, and freeing it means cutting it into pieces and removing the firebrick or masonry that locks it in place.

The new damper is set level at the required height, with its control positioned to reach the room. Disturbed firebrick is relaid in refractory mortar, and the mortar is allowed to cure for the time its maker states before the first fire. The estimate for this job shows how much masonry the swap disturbs, because that is what sets its size.

What we check before calling the damper done

Four things have to be true before a damper repair counts as finished. The handle or crank moves the plate through its full travel without force. The plate reaches its fully open position and stays there. It closes flat on its seat with no gap visible under a light. And the handle positions are clear to whoever lights the next fire.

We run those checks with you watching, before we pack up. If any one of them fails, the job is not finished, and we say what is still needed. The result is written on the invoice, with the parts used, so the next inspection starts from a known condition.

Opening the damper before the first match

A surprising amount of damper trouble starts with the order of steps. The damper opens fully before any paper or wood is lit, and it is checked by feel or with a light, not assumed from the handle position. A handle can read open while a broken link leaves the plate shut.

After a repair, we show you how your control should feel at each position. A crank has a set number of turns from closed to open. A poker rod sits on its last notch when fully open. Knowing that feel lets you notice a problem early, before a fire exposes it.

Damper findings written down before pricing

Plate condition graded: rust loss, warp and pivot wear
Replacement plate matched by frame size, pivot style and handle lug
Rain entry above the damper, with a flue cap priced separately
Whether the fireplace can be used while a part is ordered

Damper questions from Sunbeam homeowners

Can a rusted damper be saved?

Often, when the rust is on the surface and the pivots still have their metal. A plate that has thinned, holed or warped is replaced. We grade it on the visit and show you what we found.

What does the damper visit in Sunbeam cost me?

The inspection is free, and the repair is priced in writing before any work. Book the damper job within 72 hours of that inspection and 10% comes off as well.