Cracked flue tile repair in Ponte Vedra Beach

Top tiles replaced from the roof or joints resurfaced with a listed system, sized so your Ponte Vedra Beach fireplace still draws.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local flue pros for Ponte Vedra Beach chimneys

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Your Ponte Vedra Beach flue is mapped tile by tile before any repair is priced.

Free inspection and estimateThe flue at your Ponte Vedra Beach home is swept, examined from both ends and mapped at no charge.
100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.

Call (904) 920-5495 Free Inspection

A flue defect listed in a sale report

Chimney findings in a home sale report often read as cracked flue liner, further evaluation recommended. That gives a buyer a worry and a seller a deadline, but no scope.

Our visit turns the line into a plan. We locate each defect by height, say which repair suits it and put a price beside it, so both sides can agree on the same work. Buying or selling in Ponte Vedra Beach with a flue on the report? Share that page when you phone (904) 920-5495; our specialists inspect the flue for free.

TPC Sawgrass is located in Ponte Vedra Beach. Ponte Vedra Beach is in St. Johns County.

Tile, joint, seal and size

Cracked and gapped sections coated with a listed resurfacing system
Gaps at the smoke chamber closed
Cure time respected before the first fire
Flue mapped at your Ponte Vedra Beach home before any price is given

Call (904) 920-5495 Free Inspection

How chimney flue repair runs

Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.

Storm season and cracked top tiles in Ponte Vedra Beach

In NOAA's hurricane season, gusts on an exposed coastal chimney can knock a cap loose and chip the top tile.

After a storm in Ponte Vedra Beach, a look at the flue top from the ground is worth doing, and a cracked tile is a quick repair from the roof.

10% off any service booked within 72 hours of inspection

The 72 hours for flue work in Ponte Vedra Beach start at your own inspection.

Call (904) 920-5495 Free Inspection

The gap between tile and chimney wall

Clay tiles are not meant to be packed solid against the chimney wall around them. The code separates tile from brick with a gap of air or insulation, never thicker than the liner wall, supports each tile on all sides and allows only enough mortar to make the joint.

That gap lets the hot tile expand without pushing on the cooler masonry. A flue packed solid with mortar behind the tiles loses that room, and tiles can crack as they heat. When we find a solidly packed flue, it goes on the estimate as a factor in the repair choice, because tiles set that way tend to crack again.

Flues that serve an appliance

For a flue connected to an appliance, the code sets a simpler floor: the flue is not to be smaller than the connector from the appliance (R1003.14). A flue shrunk by a repair below that size can spill gases at the appliance.

The code also points gas appliance flue linings to its fuel gas chapter, and the appliance's own instructions may set further limits. So before repairing a flue that serves a furnace or water heater, we read the appliance's rating plate and connector size. The repair method is chosen to keep the flue at or above what that appliance needs.

Checking the flue once the repair is done

Finished work is checked from both ends of the flue. Replaced tiles are examined for alignment and smooth joints. A resurfaced flue is examined for full coverage, with no crack or joint left showing, and the coat is left to cure for the time its system specifies before any fire.

The flue size is measured again after resurfacing, to confirm it still meets what the fireplace or appliance needs. The results go on the invoice with the method and materials used, so the next yearly inspection has a record of what was done and where.

What goes on the flue map in Ponte Vedra Beach

Offsets and bends noted with their height and angle
Refractory mortar to ASTM C199 named for any tile reset
Gaps at the smoke chamber and at the top end of the lining
Inlet thimble and cleanout door condition on appliance flues

Before a flue repair is chosen

Can one cracked tile be fixed on its own?

If it is the top tile, often yes, from the roof. A single cracked tile lower down usually cannot be reached alone, so it is covered by resurfacing that section or by relining, depending on the rest of the flue.

Is flue repair cheaper than relining?

When the damage suits a repair, it is usually the smaller job. When it does not, stacking repairs on a failing flue costs more in the end, and we price relining instead so you can compare.