Local chimney chase cover replacement in Ortega
A cover that sheds water, keeps its pipe clearance and fits over the siding, made for your Ortega chase by local pros who inspect it free.
- Family owned and operated
- Free inspection and estimate
- Same-day service available
- Upfront pricing, no hidden fees
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
or call (904) 920-5495
About Us
Chase cover experts Ortega families can reach directly
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off when you book today
Before any metal is cut for chimneys in Ortega, we read the fireplace maker's drawing, because collar heights and pipe gaps differ by model.
- Free inspection and estimateWe measure your Ortega chase and look under the old top at no charge before anything is quoted.
- Upfront pricing, no hidden feesMetal, gauge and any framing repair each get their own priced line, and that total is what you pay.
- Workmanship warrantyThe new top, its collars and its fasteners are covered by our workmanship warranty, written on the estimate.
A chase top that holds a puddle
Water standing on a chase top a day after rain means the sheet is flat or sagging. A top cut from a single flat sheet has no shape to shed water, and thin metal bows under its own weight between the framing edges. The puddle keeps the metal wet long after the shingles around it have dried, which is where pinholes and rust begin. A replacement for a chase in Ortega is formed with cross-breaks or a fabricated pitch so water runs from the pipe collar toward the edges and off the drip, and it is checked with a hose before we leave. Have the fireplace model handy when you call (904) 920-5495 from Ortega; the manual sets the cover.
More than about six miles separate Ortega from the coast. Ortega lies roughly 7 miles from Jacksonville, measured directly rather than by road.
Our Services
Your chase top job, part by part
- New top pitched or cross-broken so rain runs to the edges
- Small gap at each pipe left open, as the manuals require
- Storm collar refitted and sealed where the maker's steps say
- Skirt turned down over the siding, ending in a drip
How It Works
How our chase cover pros replace a top in Ortega
-
Chase and pipe measured
On the free visit we measure the outside of the chase over the siding and read the fireplace model from its plate or manual.
-
A top made to your chase
The cover is formed with cross-breaks or a pitch, a skirt with a drip edge and a raised collar sized to your pipe.
-
Old top off, new top fastened
We pull the old cover and check the framing, then fasten the new top through its skirt and clamp a sealed storm collar at the pipe.
-
Hose test before we leave
Water run over the new top has to leave from every edge. If it puddles anywhere, we reshape it before the job is done.
Where We Work
Heavier gauge for Ortega chase tops
Thin sheet dents under a ladder foot or a falling limb, and each dent turns into a small basin. In Ortega, where rain rather than salt is the main load on the metal, those basins are what rust through first.
We quote a heavier gauge than the fireplace maker's minimum on wide chases, and the gauge is written on the estimate.
10% off your first service when you book today
A made-to-measure chase top for your Ortega home, 10% off as a first service booked today.
Measuring over the finished siding
The framing inside a chase is built to a size, but the chase you see from the roof is larger by the thickness of its sheathing, siding and trim. Lap siding adds a stepped profile, and corner boards stand out further still. A cover made to the framing dimensions will sit inside the siding instead of over it, and water will run straight into the joint. So the four sides are measured at the top over the finished surface, the diagonals are checked for square, and the skirt is sized to clear the thickest point with room to fasten.
A water heater or furnace vent in the same chase
Some chases carry a vent from a heating appliance or water heater next to the fireplace chimney. That vent is its own listed system, with its own maker's cap and clearances, and the chase top treats it as a separate penetration. It gets its own collar sized to its pipe and its own storm collar, spaced from the fireplace pipe as its instructions require.
We do not change that appliance's vent or cap. If its cap or storm collar is damaged, we name the problem and who should replace it, so the fix stays within that system's own instructions.
Color finishes and what sits under them
Some owners want the chase top to match the roof or the trim. Painted and powder-coated finishes can be ordered on several metals, and the color is chosen with you. The finish is cosmetic. It protects the surface until it is scratched, chipped by a ladder or worn at a fold, and after that the metal underneath is what resists the weather.
So we choose the metal and gauge for the exposure first and add the color second, rather than letting a paint finish stand in for a better metal. A touch-up of chips during later chimney service keeps the finish looking right.
Free Inspection
Measured and noted on Ortega chase tops
- Metal, grade and gauge of the new top, stated in writing
- Storm collar replaced or refitted, sealed where the manual specifies
- Listed termination cap reused, or replaced with the maker's part
- Roof covering issues near the chase, referred to a roofer in writing
FAQ
Before you order a new chase top
Will you replace the cap on the pipe too?
Only if it is damaged, and then with the part the fireplace maker lists for that model. A sound listed cap is reinstalled over the new cover.
What metal do you recommend for a chase top?
It depends on the size of the chase and the exposure. Our starting point is stainless steel in a heavier gauge than the minimum, and the estimate names the grade and gauge.
Our Services
More services in Ortega
-
-
-
-
-
-
Learn more about chimney chase cover replacementAll services in Ortega
A drained, fitted chase top for Ortega
Our family business sends a chase cover pro to measure your Ortega chase at no charge. Call (904) 920-5495.
Free Inspection