Wood stove insert installation in O'Neil
Each wood insert fitted in O'Neil carries an EPA Step 2 label and goes in to its listing, after a free inspection.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local insert pros who install to the listing
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
An insert in O'Neil goes in only after the fireplace has been measured against the insert's own table.
- Free inspection and estimateYour O'Neil firebox, chimney height and hearth are measured against the insert's manual at no charge, before anything is ordered.
- Upfront pricing, no hidden feesEvery part of the job is priced before ordering, from repairs to the rain cap, and nothing is added without your yes.
- 100% satisfaction guaranteedIf the insert smokes or draws poorly after installation to its manual, we come back and set it right.
Two appliances, one flue
Chimneys sometimes carry more than one flue, and sometimes one flue has served two appliances. A wood insert needs a flue of its own, and insert manuals say so directly, because shared flues let one appliance's smoke find its way into the other. An old furnace or water heater vent is the usual surprise.
We check how many flues the chimney has and what else might be connected before planning the liner run, and the estimate shows the route the liner takes. Chimney shared with another appliance at your O'Neil house? Have us check it at (904) 920-5495.
O'Neil is part of Nassau County. O'Neil lies near the coast.
What fireplace insert installation covers in O'Neil
- Full-length stainless liners sized to the collar
- Surrounds sealed or left open per the manual
- Blower outlets planned with an electrician
- EPA Step 2 labels checked on every new insert
How insert installation runs
-
Measure against the manual
Firebox, chimney height, hearth and clearances are checked against the insert's table before ordering.
-
Repair and clean first
Fireplace repairs are made and cured, and the flue is cleaned before the liner goes up.
-
Liner, plate and cap
A listed stainless liner runs to the top, closed with a top plate and a rain cap.
-
Set, seal and fire
The insert and surround go in as the manual directs, and the first fire is run with you.
An insert a few miles from the beach
O'Neil sits a short way inland, near enough to the coast that salt reaches a chimney top. For an insert, the exposed parts are the liner's top plate and its rain cap.
We check both when we install and on each later visit in O'Neil.
10% off any service booked within 72 hours of inspection
Book on inspection day or two days later, and the insert comes 10% off either way.
When the surround is sealed to the face
Sealing the surround panels to the fireplace face is not automatic. One maker seals them when the insert draws its air from outdoors, and leaves them unsealed when it draws room air, so enough air reaches the fire through the fireplace cavity.
For a factory-built fireplace, the same maker requires the surround or the damper area around the liner to be sealed so room air does not enter the chimney cavity. We follow the manual of your model and your fireplace type rather than a habit, and the ticket notes how the surround was set so a later service visit leaves it the same way.
Ash in the insert and where it goes
Ash builds up inside an insert, and one maker suggests removing the excess once it is 3 to 4 inches deep and the fire is out and cool, leaving about an inch as a base for the next coal bed.
The ashes go into a metal container with a tight-fitting lid, set on a noncombustible floor or the ground away from anything that burns until final disposal, with nothing else placed in that container. We bring this up at the walk-through because a paper bag of warm ash near the hearth is an easy mistake to avoid.
Driftwood and salt near the coast
Wood that has sat in salt water is a poor fuel for an insert. One maker lists salt water wood among the materials not to burn, because the chlorides it carries rapidly destroy metal surfaces and void the warranty.
Near the coast, driftwood can look like free fuel for the season. We point this out at the walk-through, along with treated wood, garbage and the other items the same maker bans, so the steel firebox, the baffle and the liner are not eaten from the inside. A stack of driftwood by the hearth is worth moving outside for good.
Measured in O'Neil before an insert is ordered
- Mantel, side facing and side wall clearances measured to the label
- Outside air through the ash chamber where the fireplace allows it
- EPA Step 2 label read and the model and serial number recorded
- First fire run with you, covering the air control and loading
Before you order an insert
Will the insert need electricity?
Only for a blower, if the model has one. It plugs into a grounded outlet, and an electrician adds one where none is within reach.
Is the inspection before an insert free?
Yes. Measuring the firebox, checking the chimney and writing the estimate cost nothing, and the price is set out upfront. Order the insert within 72 hours of that visit and the job is 10% off.
More services in O'Neil
-
-
-
-
-
-
Learn more about wood-burning fireplace insert installationAll services in O'Neil
Insert questions, free visit
Cold room, open fireplace in O'Neil? A free visit tells you whether an insert will fit.
Free Inspection