Gas fireplace inserts installed in Northside homes
A cleaned chimney, listed liners and a sealed firebox: gas insert installation in Northside done by the manual.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Gas insert experts for Northside homes
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Old wood chimneys are cleaned before any gas appliance connects, as the fuel gas code asks.
- Free inspection and estimateThe opening, flue and mantel of your Northside fireplace are measured against the insert's plate at no charge.
- Upfront pricing, no hidden feesInsert, vent kit, surround, cleaning and repairs are priced line by line, and the gas and power trades are named.
- 100% satisfaction guaranteedIf the insert does not light, burn or seal the way its manual describes after our installation, we come back.
Inserts and factory-built fireplaces
Metal, factory-built fireplaces raise a separate question. Some gas inserts are listed for masonry fireplaces only, and a factory-built unit's own manual may not allow an insert in it at all. The plate on a factory-built unit usually sits inside the opening or behind the lower grille, and it names the model we look up.
Both rating plates get read before anyone says yes, and a no is given on the first visit along with the options that remain. Factory-built fireplace at your Northside house and wondering about gas? Check with us first at (904) 920-5495.
Northside is a neighborhood inside Jacksonville city limits. Northside sits in Duval County.
What gas insert installation covers in Northside
- Sealed direct-vent gas inserts installed to their manuals
- Chimneys cleaned before any gas appliance connects
- Co-linear liners run to a listed termination
- Dampers removed or fixed open for the liners
From wood fireplace to gas insert in Northside
-
Measure against the plate
Opening, flue and mantel are checked against the insert's rating plate and manual.
-
Clean and check the chimney
The old flue is cleaned, examined and repaired if needed before the liners go up.
-
Liners, insert, surround
The vent kit runs to its termination, the insert is set and the surround fitted.
-
Hookups and first light
The gas and electrical hookups are made, then we light and test the insert with you.
Chimney height inland in Northside
Co-linear liners have height limits, and chimneys in Northside vary. One maker sets 10 to 40 feet of vertical liner.
We measure yours before recommending a kit.
10% off any service booked within 72 hours of inspection
Vent and start-up included, a gas insert in Northside comes 10% off.
Ignition and the flame safeguard
Under section 602.2 of the fuel gas code, the main burner must be lit by a pilot, an igniter or direct ignition, and a flame safeguard has to prove the flame. The safeguard shuts the gas off if the burner or pilot is not proven lit.
On install day we watch that sequence work: the pilot or igniter lighting, the burner catching and the safeguard holding the valve open only while there is flame. One maker describes a light-up of 5 to 10 seconds across all burner openings as satisfactory, and a slow or patchy light-up is corrected before we leave.
How tightly a liner may bend
Flexible liners can kink if they are forced around a tight corner, and a kink narrows the passage. One maker sets a minimum bend radius of 3 inches for its intake liner and 4 inches for its exhaust liner.
The tightest spots are usually at the throat and the smoke shelf, where the liners turn from the insert's adapter into the flue. We plan the route through those spots before pulling the liners, and where the damper frame or smoke shelf crowds the bend, the estimate says what is trimmed or removed to keep the radius.
One gas, set at the factory
Natural gas or propane is decided at the factory, and the rating plate says which. The orifices, pressures and sometimes the valve differ between the two, and a unit is converted only with its maker's conversion kit.
We confirm the gas at the house and the gas on the plate before the insert is delivered. Where a conversion is needed, the kit is ordered with the insert and fitted as its instructions say, with the conversion label applied. Running an insert on the wrong gas is not something to adjust around; it is corrected before first light.
Opening, flue and mantel on paper
- Fireplace opening width, height and depth against the insert's plate
- Co-linear or co-axial kit chosen from the insert's manual
- Mantel height and projection measured against the plate
- Barrier screen fitted and relief doors checked
Gas insert questions from Northside
What is co-linear venting?
Two flexible liners run up the old flue, one bringing outdoor air in and one taking exhaust out. They join the insert at the bottom and a termination at the top.
Can a gas insert go in a metal fireplace?
Some inserts are listed for masonry fireplaces only. Others may go into a factory-built unit whose own manual permits it, and we read both first.
More services in Northside
-
-
-
-
-
-
Learn more about gas fireplace insert installationAll services in Northside
Easy heat from the fireplace in Northside
Call (904) 920-5495 for a free gas insert check in Northside; an install booked within 72 hours of it comes 10% off.
Free Inspection