Family-owned smoke chamber repair in Fleming Island

Debris on the smoke shelf, cracks in the chamber, rust on the damper frame, all checked in Fleming Island on one free visit.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Smoke chamber pros who measure before they trowel

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Refractory mortar made for fireplaces goes on the walls, named on your ticket.

Free inspection and estimateWe look above the damper in your Fleming Island fireplace, measure the chamber and write down what we find at no cost.
Upfront pricing, no hidden feesCleaning, resets, parging and cure time are priced line by line before the first trowel goes in.
Family owned and operatedA family-owned local crew does the reaching and troweling through the throat, and cleans up after itself.

Call (904) 920-5495 Free Inspection

A cold fireplace that smells of smoke

A house that draws air in through its chimney draws the smell of old deposits in as well, and a rough smoke chamber holds plenty of them on its steps and ledges. Sweeping helps, but a stepped chamber keeps catching soot faster than a smooth one. The smell can be stronger on days when exhaust fans or the air handler are pulling on the house.

When a fireplace in Fleming Island smells while it is not in use, we check the chamber surface, the damper seal and the flue top together, and write down which of them the repair should start with.

At the 2020 Census, Fleming Island was home to 29,142 people. Fleming Island is inland.

Smoke chamber work we take on in Fleming Island

Stepped chamber brick cleaned to bare masonry
Flaking parge coats removed and redone
Your Fleming Island fireplace protected while we work above it
Chamber findings in Fleming Island written wall by wall

Call (904) 920-5495 Free Inspection

From the first look above the damper to the first fire in Fleming Island

Tell us what the fireplace does
Spilling smoke, a stale smell or grit on the damper plate tells us what to bring to the free visit.
Chamber measured and mapped
Height, width and wall slopes are measured, and each wall, the shelf and the flue transition are checked.
Cleaned, reset, parged
Soot and glaze come off, loose units are reset, joints filled, then refractory mortar goes on in layers.
Cured and draft tested
The product cures as its data sheet directs, then a small fire shows how the fireplace draws.

Deposits and the inland fireplace in Fleming Island

How much soot and tar a chamber collects depends on the wood and the fire, not on the distance to the coast. In Fleming Island, dry wood burned hot leaves less in the chamber than damp wood left to smolder.

A smooth chamber helps either way, and we pass on the burning tips that help it stay clean.

10% off any service booked within 72 hours of inspection

The room stays covered while we work, and the chamber job comes 10% off.

Call (904) 920-5495 Free Inspection

Open joints in the chamber walls

Heat, acidic condensate and water wear mortar out of chamber joints, leaving gaps between the bricks. Those gaps lead into the body of the chimney, where heat and smoke were never meant to go, and they hold deposits a brush cannot reach.

We rake out loose material and fill each open joint with refractory mortar before any parging goes on. Filled joints under a smooth coat are what keep the chamber sealed; a coat stretched over hollow joints cracks along them. Filling them also stops the joints from carrying heat into the masonry behind the chamber.

Cure time before the first fire

Refractory mortar needs time to cure before it sees fire, and the data sheet gives both the wait and the way to bring it up to heat. A full fire lit on a fresh parge coat drives water out too fast and can crack it.

The cure time and the first-fire instructions for the product we used go on your ticket with the finish date. If you want the fireplace ready for a particular day, tell us when you book, and the schedule is built around it. A small first fire, as the data sheet describes, lets the last moisture leave without cracking the coat.

Why steps collect deposits

Each step in a corbeled chamber is a ledge. Soot and tar settle on ledges, and the rough, turbulent surface cools the gases so more of them condense there. A brush sweeps the faces of the steps but leaves the corners behind.

Creosote that builds up in those corners is fuel sitting in the path of fire gases. A smooth parge coat gives it nowhere to hide and lets the next sweep reach the whole surface, which is the main safety reason for the work. A smooth chamber is also easier to inspect, since a crack or an open joint stands out plainly against the parge coat.

Shape, walls, shelf and product, in writing

Chamber height and opening width measured and written down
Wall slopes checked against the 30 and 45 degree limits
Smoke shelf cleared, repaired and shaped to drain to the firebox
Cure time and first-fire instructions written with the finish date

Smoke chamber questions from Fleming Island

Will the work make a mess in the house?

The opening is sealed while we work, the floor is covered and the debris is vacuumed at the source. We clean the firebox before we leave.

Does a factory-built fireplace have a smoke chamber to repair?

Those units have no masonry smoke chamber, so this service does not apply to them. Their internal parts are repaired with the maker's listed pieces, which is a different job we also handle.