Electric fireplace heater repair in Fernandina Beach

From a slipped flicker rod to a failed control board, Fernandina Beach electric fireplace repairs done by a family crew.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local electric fireplace pros for Fernandina Beach homes

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Inserts and wall units are handled with the trim and wall protected.

Free inspection and estimateYour Fernandina Beach unit is tested part by part, from the outlet to the board, at no charge.
100% satisfaction guaranteedIf the repaired unit does not heat, light and respond as its manual says, we return and put it right.
Family owned and operatedThe family crew that traces the fault in your unit is the crew that repairs it.

Call (904) 920-5495 Free Inspection

The fan blows, but the air is cold

Cool air from an electric fireplace set to heat means the fan works and the heater circuit does not. Somewhere between the control and the element, the path is open: the element itself, the thermostat, a tripped thermal cutoff or the relay on the board that switches the heat. A heater that has just been reset and still blows cold goes straight to the meter tests.

Each of those has a test, and we run them in order rather than guessing at the dearest part. The one that failed is named, priced and ordered by your model's part number. Fireplace blowing cold at your home in Fernandina Beach? Call (904) 920-5495, and our repair specialists will diagnose it for free.

Fernandina Beach is on the coast. Amelia Island Light lies within Fernandina Beach.

Electric fireplace repairs we handle in Fernandina Beach

Noisy fan motors replaced by part number
Flicker rods reseated and motors replaced
Wall units lifted off and rehung level
Airways cleaned of dust and pet hair

Call (904) 920-5495 Free Inspection

How our repair pros fix an electric fireplace in Fernandina Beach

Model number first
Read us the rating label, and parts availability is checked before the visit.
Supply, then each part
The outlet and breaker are checked, then heater, fan, flame effect, board and remote are tested in order.
Failed part replaced
The maker's part for your serial number is fitted, with any electrician work done separately.
Retested with you
Heat, flames, remote and thermostat are run through their settings before we leave.

Inserts under an idle chimney by the ocean

An electric insert sits below a chimney whose cap faces salt air. A rusted cap lets rain down toward the insert.

On insert repairs in Fernandina Beach, we check whether water has been reaching the firebox from above.

10% off any service booked within 72 hours of inspection

Fixing an electric fireplace at your Fernandina Beach home? The repair keeps our workmanship warranty with 10% off the price.

Call (904) 920-5495 Free Inspection

Two appliances in one cabinet

An electric fireplace is really two appliances sharing a box. One is a fan-forced heater: a resistance element, a small fan, a thermostat and a thermal cutoff. The other is the flame effect, where lights play across a spinning rod or run a stored sequence behind a screen.

A control board ties them together and listens for the remote. Because the two halves work independently, the symptoms tell us where to look. Heat without flames points to the light side. Flames without heat points to the heater side. Nothing at all points to the supply or the board. The board sits between both halves, so it is tested after the supply and before any part is condemned.

Diagnosing the control board

The control board takes the button presses and remote signals and switches the heater, fan and lights. When it fails, the symptoms can look like anything: no response, a heater that will not switch on, lights that stay on or an error on the display.

Because the board is often the dearest part, we rule out the cheaper causes first: power, connectors, the main switch, the receiver and any lock setting. Only when those check out is the board replaced. Boards are ordered by model and serial number, since makers sometimes change boards within a model's run. Any connector that shows heat damage near the board is replaced along with it.

Ordering parts by model and serial

Model and serial, both printed on the unit's rating label, decide which part fits. Makers sometimes change parts partway through a model's production, so the model alone is not always enough.

We order through the maker or its parts distributors using both numbers. Where a part has been superseded, the maker's replacement is used. That care avoids the delay of a part that almost fits. The part number and expected arrival go on the estimate before we order anything. If a part is on backorder, you hear the expected date before deciding whether to wait.

What we test on units in Fernandina Beach

Rating label copied: model, serial, volts and watts
Connectors inside the unit checked for fit and heat marks
Insert, wall unit or recessed unit removal allowed for
Parts used and tests done written on the invoice

Before a part is ordered

Can you get parts for an older model?

Usually, through the maker or its parts distributors, ordered by model and serial number. A discontinued part is flagged to you before any charge.

The flames stopped moving. Is that expensive?

Often not. A flicker rod that has slipped off its motor shaft is a quick fix. A failed motor is replaced with the maker's part, which is still a modest repair.