Stone chimney repair in Bryceville, stone by stone
One free visit in Bryceville settles which build your stone chimney is and what the right repair costs.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local stone masons who match mortar and joints in Bryceville
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Old cement and caulk come out before new mortar goes in.
- Free inspection and estimateWhether your Bryceville chimney is full stone or veneer is settled on a free visit, before any price.
- Upfront pricing, no hidden feesStones, joints and veneer area are priced in writing one line at a time.
- Family owned and operatedOur family-owned masons approve the mortar sample with you before the first joint is filled.
A stone cracked straight through
A stone cracked through its body, not along a joint, may have been hit, stressed by movement around it, or split along a weakness in the stone. A single cracked stone can be replaced. A crack that runs through several stones in a line is a different kind of finding. Replacing a single cracked stone is routine work; tracing a crack across several is not.
We look at the stones around a cracked unit on your chimney in Bryceville before quoting, since a crack that continues into its neighbors points to movement, not to one bad stone. The estimate says which it is.
The county for Bryceville is Nassau County. Bryceville is inland.
What our stone masons fix in Bryceville
- Water barrier and lath repaired behind veneer
- Bulging anchored veneer secured or rebuilt
- Old cement patches and caulk removed
- Dry-stack veneer refitted tight
Identify, rake, reset, match
-
Describe what moved
Tell us what has shifted or fallen, and the free visit comes equipped for it.
-
Build and backing confirmed
Corners, joints and the base show the build, and a loose piece shows what is behind the veneer.
-
Reset, repoint or reinstall
Stones go back on fresh beds, joints fill in layers, and veneer returns to a repaired backing.
-
Matched and cured
An approved mortar sample and the old joint profile guide the finish, and the cure time is written down.
Cleaning an inland stone chimney in Bryceville
Inland in Bryceville, stains on stone come from water, smoke and plant growth rather than salt. Gentle cleaning, tested first, takes most of it off.
If a stain keeps coming back, we look for the water or smoke behind it.
10% off any service booked within 72 hours of inspection
On a stone chimney in Bryceville, the mortar match and the discount both go in writing.
How deep stone joints are raked
Preservation Brief 2, the Park Service's repointing guide, ties rake depth to joint width, asking for a cut two or two and a half times as deep as the joint is wide, and warns that wide stone joints can need clearing several inches back before firm mortar appears.
Stopping short leaves new mortar sitting on crumbly mortar, and it falls out with it. We rake until the chisel meets firm mortar, mostly by hand on stone, since a grinder blade can nick the edges of irregular stones. On irregular stone, the depth is checked joint by joint, since one joint may be sound an inch in while its neighbor is soft far deeper.
Resetting a loose stone
A loose stone comes out, and both the stone and its bed are cleaned down to sound mortar. The stone goes back on a fresh bed, adjusted to line up with its neighbors, and the joints around it are packed and tooled once the bed has firmed.
If the bed behind the stone has turned to sand deep into the wall, resetting one stone will not hold, and the repair widens to the area around it. We tell you that before starting, with the extra stones counted, rather than after the first stone is out. Small stone spalls or wedges are used to hold the stone in line while its bed sets, then removed or hidden in the joint.
Removing hard cement patches
Portland cement patches spread over stone joints are harder and less permeable than the stone or the original mortar. Moisture that cannot leave through the patch leaves through the stone, and hard patches can crack the stone edges they cover.
Taking them out is slow work, done by hand along the joint so the stone edge survives. We price the removal separately from the repointing, because a chimney with a lot of old patching takes longer before any new mortar goes in. Where a patch has already cracked a stone edge, that stone is reset or replaced along with the joint.
Stone, joints, backing and base, in writing
- Joints raked to sound mortar and filled in layers
- Joint profile matched to the existing work
- Old cement patches and caulk cut out before repointing
- Access equipment and roof protection listed on the estimate
Stone chimney questions from Bryceville
Why not just seal the joints with caulk?
Caulk keeps water in as well as out, so the mortar behind it stays wet and fails. Repointing with the right mortar lets the joint dry the way it should.
Do you repair manufactured stone veneer as well as natural stone?
Yes. Manufactured veneer follows its maker's installation guide for the backing and setting mortar, and we match the product line and color as closely as it allows.
More services in Bryceville
-
-
-
-
-
-
Learn more about stone chimney repairAll services in Bryceville
Masons for stone chimneys in Bryceville
Our masons identify the build, check the joints and price each stone in Bryceville before work starts. Call (904) 920-5495.
Free Inspection