Local chimney rebuild in Bellair-Meadowbrook Terrace

Planned before the first brick comes off, your Bellair-Meadowbrook Terrace rebuild has its take-down line, flue, height and crown set during a free inspection.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Chimney rebuild specialists who test every course

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Every course is tested by hand, so the take-down stops at brick that holds.

Family owned and operatedOur family business takes your Bellair-Meadowbrook Terrace chimney down by hand and lays it back up itself.
Upfront pricing, no hidden feesThe take-down line, flue plan and crown are priced before the first brick comes off.
Workmanship warrantyFrom the new courses to the counterflashing, the rebuilt stack carries our workmanship warranty.

Call (904) 920-5495 Free Inspection

Cure, cap and first fire after the rebuild

New mortar and a cast crown need time to cure before they carry weight, heat or water, and the product data sheets set that time. The cap and any liner top plate go on after the crown has cured, so their fasteners do not crack green concrete.

The first fire comes last: a small one, watched, to confirm the draw through the rebuilt flue. You know in advance the date your Bellair-Meadowbrook Terrace chimney can be used again, and the written record lists what was built. Keep that record with the house papers for the next inspection. Chimney leaning in Bellair-Meadowbrook Terrace? Our masons mark where sound brick starts, and it takes one call to (904) 920-5495.

The county for Bellair-Meadowbrook Terrace is Clay County. At the 2020 Census, Bellair-Meadowbrook Terrace was home to 14,482 people.

A rebuild from take-down to cap

Brick lowered by bucket or chute, never thrown
Flue tile set in refractory mortar or a listed liner run
Cap anchored once the crown has cured
Work days and cure time for the Bellair-Meadowbrook Terrace job in writing

Call (904) 920-5495 Free Inspection

Test, take down, relay, crown

Courses tested, line marked
Each course is pressed and probed from the top down, and the take-down line is marked where sound brick starts.
Taken down under cover
The flue is plugged and the roof protected, then brick comes off by hand and sound units are saved.
Relaid with flue and flashing
Courses go back plumb in the chosen mortar, the flue tile or liner rises with them, and counterflashing is set into the joints.
Height, crown and cap
The height is checked, a crown is cast with a drip edge and bond break, and the cap goes on after it cures.

Height checks on rebuilt chimneys in Bellair-Meadowbrook Terrace

A rebuilt stack must stand at least 3 feet above where it passes the roof and 2 feet higher than anything within 10 feet, as the code requires.

If an addition or a new roof has changed that, the rebuild in Bellair-Meadowbrook Terrace adds courses before the crown is cast.

10% off any service booked within 72 hours of inspection

Rebuilds booked within 72 hours of the inspection come 10% off.

Call (904) 920-5495 Free Inspection

Closing the flue while the stack comes down

The open flue is the easiest path for rubble into the house. Before the first course comes off, a cover or a plug goes into the flue a few feet down, so mortar and brick fragments stop on top of it instead of landing in the smoke chamber or on the damper.

Inside, the fireplace opening is sealed as a second barrier. The cover is lifted and cleaned out as the take-down goes lower, and it stays in place until the new flue work begins. A cover that fills with debris is emptied by hand rather than pushed down the flue.

Setting new clay tile in a rebuilt stack

When the rebuild uses clay flue tile, each section is set in medium-duty, water-insoluble refractory mortar to ASTM C199, with tight joints struck smooth on the inside so they do not catch deposit. The tile is supported on all sides.

It is not mortared solid to the brick around it. The code calls for an airspace, or insulation no thicker than the tile itself, between the tile and the inner face of the chimney wall (FBC R1003.12), so the tile can expand with heat without cracking the masonry. Each tile is checked for plumb and a clean joint before the next course of brick rises around it.

The divider between two flues

Where two or more flues run in one chimney, the code wants masonry built between them, a wythe not less than 4 inches thick (FBC R1003.13). That divider keeps smoke and heat in one flue from crossing into the next through an open joint.

In old chimneys the divider can be broken, thin or missing near the top. A rebuild puts it back to full thickness through the rebuilt section and ties it into the outer walls. Each flue's tile or liner is then set on its own side of the divider. Where one flue is abandoned, the divider still goes back, since the empty flue beside it still collects heat and water.

Take-down line, flue and crown plan

Mortar type chosen from ASTM C270 to suit the brick and exposure
Height checked against the roof and anything within 10 feet
Cure time allowed before the cap goes on and the first fire
Permit expectation, who files, and where inspections fall in the schedule

Rebuild questions from Bellair-Meadowbrook Terrace

Do you rebuild chimneys in Bellair-Meadowbrook Terrace?

We do. Describe what you are seeing on the chimney and the roof type, and the Bellair-Meadowbrook Terrace estimate visit is planned around testing the masonry.

Does a rebuild qualify for the 10% offer?

Yes. A rebuild booked within 72 hours of the free inspection comes 10% off; just ask for it on the call.