Stone veneer chimney repair for Bellair-Meadowbrook Terrace homes

A local family business for stone chimneys in Bellair-Meadowbrook Terrace, with 10% off stone work you book inside three days of the inspection.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Stone chimney specialists for Bellair-Meadowbrook Terrace homes

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Stones reset and replaced on your Bellair-Meadowbrook Terrace chimney are counted on the ticket.

Free inspection and estimateWhether your Bellair-Meadowbrook Terrace chimney is full stone or veneer is settled on a free visit, before any price.
Upfront pricing, no hidden feesStones, joints and veneer area are priced in writing one line at a time.
Family owned and operatedOur family-owned masons approve the mortar sample with you before the first joint is filled.

Call (904) 920-5495 Free Inspection

Veneer sitting right on the roof shingles

Stone veneer that runs down onto the roof surface, with no gap, soaks up water from the roof and holds it against the base of the stone. Veneer makers' guides call for a gap between the stone and the roofing, with flashing detailed behind it. The wet base can also let water behind the veneer, where it has no easy way out.

Where the veneer on a chimney in Bellair-Meadowbrook Terrace sits on the shingles, we cut it back to the gap its maker specifies and correct the flashing detail behind it. The estimate shows both, since one without the other does not stop the water.

Bellair-Meadowbrook Terrace does not reach the coast. Bellair-Meadowbrook Terrace sits in Clay County.

From one loose stone to a veneer reinstall

Deep stone joints raked and repointed in layers
Loose adhered veneer taken off and reinstalled
Bulging anchored veneer secured or rebuilt
Every stone reset on your Bellair-Meadowbrook Terrace chimney counted on the ticket

Call (904) 920-5495 Free Inspection

From the first loose stone to the last tooled joint in Bellair-Meadowbrook Terrace

Describe what moved
Tell us what has shifted or fallen, and the free visit comes equipped for it.
Build and backing confirmed
Corners, joints and the base show the build, and a loose piece shows what is behind the veneer.
Reset, repoint or reinstall
Stones go back on fresh beds, joints fill in layers, and veneer returns to a repaired backing.
Matched and cured
An approved mortar sample and the old joint profile guide the finish, and the cure time is written down.

Movement cracks in Bellair-Meadowbrook Terrace

Cracks that step through several joints are unrelated to the coast. In Bellair-Meadowbrook Terrace, they point to movement at the footing or the top of the chimney.

Crack width and lean are measured before any repointing is quoted.

10% off any service booked within 72 hours of inspection

Say yes to the stone work within 72 hours of the inspection and save 10%.

Call (904) 920-5495 Free Inspection

Four ways a stone chimney is built

Full stone chimneys are laid in mortar course by course, and the stone carries the weight. Anchored stone veneer is a facing of full stones tied back to the chimney behind it with metal ties. Adhered veneer is a thin facing, natural or manufactured, held by mortar alone to a backing of lath over a water barrier, or set straight onto bare masonry.

Natural stone sawn thin for veneer goes up the way manufactured veneer does, and its failures look the same. Each of the four has its own repair, which is why identifying the build is the first line on every stone estimate we write. Some chimneys mix builds, with full stone below the roof line and veneer above it, and each part is priced by its own method.

Flashing against irregular stone

Flashing tucks into a joint on a brick chimney, but stone joints wander. On full stone, the counterflashing is set into a groove cut into the stone or into a joint deep enough to hold it. On veneer, the flashing belongs behind the stone, lapped with the barrier.

Sealant smeared along the top of flashing on stone is a temporary fix at best. We note how the flashing is fixed on your chimney, and when it needs rework, the estimate lists it separately from the stone repair. Where the stone is too irregular for a groove, a stepped counterflashing is fitted to the courses instead.

The cap on top of a stone chimney

The top of a stone chimney follows R1003.9.1 like any masonry chimney: a cap of concrete, metal or stone that slopes water away, overhangs to a drip, and meets the flue liner at a sealed joint that lets the two move apart. A flat mortar wash across the top stones meets none of that.

Water that leaves the top the wrong way runs down the stone and into the joints below. We check the cap on every stone chimney we work on and price crown work separately, in the order that keeps the new stone work dry. A stone cap made from a single slab or a few large pieces also needs a drip edge cut or formed underneath it.

Stone, joints, backing and base, in writing

Build identified as full stone, anchored veneer or adhered veneer
Cracked stones replaced, with the source of each match named
Water repellent recommended only after repairs have cured
Access equipment and roof protection listed on the estimate

Stone chimney questions from Bellair-Meadowbrook Terrace

Could you come out today for a loose stone in Bellair-Meadowbrook Terrace?

If a slot is open that day, yes. If a stone has already fallen, keep people clear of the base until we arrive.

Can you match my stone?

We look for the closest current match and also consider moving stones from a hidden face to the repair. You see the options and approve a sample before any stone is removed.