Local chimney crown repair in Bellair-Meadowbrook Terrace

Each new Bellair-Meadowbrook Terrace crown gets a proper bond break at the flue tile, so heat from the flue cannot crack it. Crown checks are free.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Chimney crown pros who check before they seal or recast

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Every new crown we cast gets an overhang, a drip groove and a sealed joint at the flue.

Free inspection and estimateWe map the cracks on your Bellair-Meadowbrook Terrace crown and check the brick under it at no charge.
Upfront pricing, no hidden feesCoating and recasting are both priced on paper, so you see the difference before choosing.
100% satisfaction guaranteedIf the finished crown is not right, tell us and we come back to put it right.

Call (904) 920-5495 Free Inspection

Checking a crown from the ground

You can learn a fair amount about a crown without climbing. With binoculars from across the yard, look at the top edge of the chimney: dark lines across the top are cracks, a ragged or crumbling edge suggests a failing wash, and a thin gray layer that stops short of the brick means there is no overhang.

Look below it too. Flaking or damp brick in the top few courses, or white deposits there, means water is getting in at the top. Those observations help us plan the Bellair-Meadowbrook Terrace visit before anyone goes up. One phone call to (904) 920-5495 is all a free crown inspection in Bellair-Meadowbrook Terrace takes.

The county for Bellair-Meadowbrook Terrace is Clay County. The 2020 Census counted 14,482 residents in Bellair-Meadowbrook Terrace.

What our crown work covers in Bellair-Meadowbrook Terrace

Wider cracks filled before a crown coating goes on
Forms set with an overhang past every face of the brick
Reinforcement placed inside the slab to control cracking
Fresh concrete kept damp and covered while it cures

Call (904) 920-5495 Free Inspection

Map, prep, coat or pour, cure

Crack map from the roof
We identify the type of top and sketch each crack with its width, so the choice between coating and recasting is based on what is there.
Prep for coating or removal
A sound crown is cleaned and its wider cracks filled; a failed one is broken out down to sound brick.
Coat, or form and pour
The coating is brushed on in dry weather, or new concrete goes into forms with an overhang, a drip groove and reinforcement.
Cure, seal and refit the cap
The bond break at each flue is sealed, the concrete cures under cover, and the cap goes back on.

Coating a sound crown in Bellair-Meadowbrook Terrace

Many cracked crowns in Bellair-Meadowbrook Terrace are still solid underneath. When the slab does not move under pressure and the cracks are hairline, a flexible crown coating is the right repair and the smaller bill.

We fill the wider cracks first, tape the flue tiles and brush the coating on in a dry spell.

10% off any service booked within 72 hours of inspection

Seal or recast, crown repair in Bellair-Meadowbrook Terrace earns the 10% discount.

Call (904) 920-5495 Free Inspection

Taping the flue tile before a coating

Before a crown is coated, tape goes around each flue tile, set a little higher than the crown surface. The coating is brushed up to that line, over the tile-to-crown joint, and ends in a clean edge instead of a ragged smear.

What sits in the joint where the tile meets the crown matters more than the tape. The bond break the code asks for is a flexible, caulked joint that lets the tile expand as it heats while the concrete stays put. Rigid patching cement packed into it locks the tile to the crown, and the next fire cracks one or the other. An open joint at the tile is cleaned out and resealed with a flexible sealant before the coating goes on.

Reinforcement inside a cast crown

Concrete shrinks as it cures and moves with heat afterward, and without reinforcement those movements open cracks. BIA Technical Note 19B calls for adequate reinforcement in a cast cap to control cracking from shrinkage and thermal movement, with extra where the cap overhangs the face.

The reinforcement is placed within the thickness of the crown, clear of the brick below and the surface above, so concrete surrounds it on all sides. Where a crown will stay wet for long spells, the type of reinforcement is chosen with corrosion in mind. You are told what goes in before the pour.

Fastening the cap to a new crown

A chimney cap has to be held down against wind, and how it is held matters to the crown. Screws driven down through the crown make holes that need sealing and can let water into the core of the chimney.

Where the cap design allows, its mount grips the flue tile instead, leaving the concrete with no holes in it. Where a cap must be fixed to the crown, the fasteners go in only after the concrete can take them, into sealed holes, and how the cap is attached is recorded. A cap that has worked loose before is checked for why.

Coat or recast, and the reasons

Crack map with widths, and whether the slab is still sound
Overhang, drip groove and slope for the new crown
Bond break material around each flue tile
Other findings on flue tile or brick, listed as separate lines

Crown repair questions from Bellair-Meadowbrook Terrace

Is Bellair-Meadowbrook Terrace inside your crown repair area?

It is. On your Bellair-Meadowbrook Terrace chimney we first identify the type of top and map its cracks, then put a coating or a recast in writing. Call (904) 920-5495 to book.

Will a new crown fix my leak?

It fixes a leak that is coming through the crown. If the water is entering at the flashing, the brick or the flue top, a new crown will not stop it, which is why we trace the entry point first.