Gas fireplace venting for Arlington homes

New B-vent runs in Arlington laid out from the maker's height, elbow and roof pitch limits before a hole is cut.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Venting pros who trace the whole run in Arlington

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Cap distances are taped against the code table and the maker's drawing.

Free inspection and estimateThe vent on your Arlington gas fireplace is traced from the collar to the cap and measured against the code at no charge.
Upfront pricing, no hidden feesEach section, fitting and reroute is priced on its own line before any pipe is cut or replaced.
100% satisfaction guaranteedIf the flame, the draft or the shutdown problem is not fixed by the vent repair we quoted, we come back.

Call (904) 920-5495 Free Inspection

A cap too close to the gas meter

Vent caps and gas meters both end up on the side of the house, sometimes right next to each other. A regulator and its vent outlet need space from a fireplace's exhaust, and makers spell out how much. Moving the cap is usually simpler than moving the meter, which belongs to the gas company.

Where the cap is too close, the vent is rerouted before the fireplace runs another season. Gas fireplace vent near the gas meter on a house in Arlington? Have it measured at (904) 920-5495.

Arlington is one of the named neighborhoods of Jacksonville. Arlington is part of Duval County.

What gas fireplace venting covers in Arlington

Crushed or rusted sections replaced from the listed system
Sagging runs resupported and resloped
Insulation cleared from vent air spaces
A flame check after every repair in Arlington

Call (904) 920-5495 Free Inspection

How gas fireplace vent work runs

Identify the system
The manual and pipe markings tell us the vent type, size and maker.
Trace the run
With the unit off and cool, we follow the vent and check joints, supports and clearances.
Repair with listed parts
Joints are reseated, damaged sections replaced and crowded caps moved.
Test and record
We fire the unit, check flame and draft, then note every fix.

Shrouds over vent caps in Arlington

Decorative shrouds on chimneys in Arlington can sit over a gas vent cap and choke its draft.

We check the cap has the open air it needs.

10% off any service booked within 72 hours of inspection

A vent check and repair booked within 72 hours of the trace comes 10% off.

Call (904) 920-5495 Free Inspection

Only the appliance's own vent system

Vent pipe for a direct-vent unit is not generic. One maker's manual allows only venting components approved and labeled for that fireplace, and notes that a direct-vent fireplace's venting system is tested and approved as part of the appliance, clearances included.

That means a repair uses the same maker's pipe, elbows and termination, or the ones its manual lists. Mixing brands, even when the diameters match, puts the vent outside the tested design. We read the pipe markings and the manual before ordering any section. Parts from another brand may fit the diameter and still leak at the joints.

Height limits on a B-vent

Natural-draft vents need height to draw. One maker's B-vent fireplaces need at least 8 feet of vertical vent, measured from the top of the unit to the top of the termination, and allow no more than 40 feet.

The same manual limits any horizontal portion to half the height of the vent system, measured center to center. A short or mostly sideways B-vent drafts poorly and can spill at the draft hood. We measure the system against those figures before repairing it, since a repair that keeps a failing layout keeps the problem. A tall vent can overdraw too, which is why there is a maximum as well as a minimum.

Supporting and fastening B-vent

B-vent pipe has to carry its own weight without leaning on the appliance or its elbows. One maker asks for horizontal runs to be supported at least every 5 feet and for offsets to be supported so the pipe's weight does not bear on the elbows.

The same manual says not to drive sheet metal screws through the pipe's inner liner, and fastens the first section to the firebox with self-tapping screws and plumber's strap pulled taut. We check supports and fastening along the run, since a sagging run is how joints pull apart. Straps and supports come from the vent maker's parts list, not the hardware aisle.

Traced in Arlington before any vent pipe is replaced

Elbows counted against the system's limits
B-vent height, horizontal length and roof cap height measured
Damaged sections replaced from the listed vent system
Roof covering work named for a roofer

Before the vent is opened up

Could the vent be why my gas fireplace in Arlington shuts off?

It can be. A blocked cap, a leaking inner pipe or a badly pitched run can all put the flame out. We test the vent first, then the controls.

Is the vent inspection free?

Yes. The trace and the written quote cost nothing, and the quoted price does not grow. Book the repair within 72 hours of the trace and you save 10% on it.