Family-owned smoke chamber repair in Yulee
Open joints, flaking parge or loose brick in the chamber, fixed by local Yulee specialists and backed by our guarantee.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local masons who parge smoke chambers in Yulee
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Chamber findings for your home in Yulee are written wall by wall.
- Free inspection and estimateWe look above the damper in your Yulee fireplace, measure the chamber and write down what we find at no cost.
- Upfront pricing, no hidden feesCleaning, resets, parging and cure time are priced line by line before the first trowel goes in.
- Family owned and operatedA family-owned local crew does the reaching and troweling through the throat, and cleans up after itself.
Rust flakes on the hearth
Flakes of rust on the hearth or the firebox floor can trace back to the damper frame, which sits at the base of the smoke chamber. Water reaching the smoke shelf keeps that frame wet, and the shelf itself can hold puddled water behind the damper. A shelf that holds water keeps the frame wet between rains, and the rust grows from there.
We look for where the water enters, such as an open or damaged flue top, and check the shelf and damper frame at your fireplace in Yulee. The top repair, the frame and the chamber work each get their own line.
Yulee is inland. Yulee lies within Nassau County.
What our masons fix above the damper in Yulee
- Chamber walls troweled smooth with refractory mortar
- Smoke shelf cleared and repaired
- Out-of-limit chambers rebuilt to shape
- Draft tested after the cure
From the first look above the damper to the first fire in Yulee
-
Tell us what the fireplace does
Spilling smoke, a stale smell or grit on the damper plate tells us what to bring to the free visit.
-
Chamber measured and mapped
Height, width and wall slopes are measured, and each wall, the shelf and the flue transition are checked.
-
Cleaned, reset, parged
Soot and glaze come off, loose units are reset, joints filled, then refractory mortar goes on in layers.
-
Cured and draft tested
The product cures as its data sheet directs, then a small fire shows how the fireplace draws.
Iron parts at an inland chamber in Yulee
Inland in Yulee, the damper frame at the base of the chamber is not fighting salt air. It rusts only where water reaches it, and a dry chimney keeps it sound for a long time.
When we find rust there, it points us to the water source, and the fix starts at the top of the chimney.
10% off any service booked within 72 hours of inspection
The room stays covered while we work, and the chamber job comes 10% off.
The 30 and 45 degree limits
The code sets two slope limits for chamber walls. Corbeled brick, stepped in course by course, may lean no more than 30 degrees from vertical. Rolled or sloped walls, and prefabricated chamber linings, may lean up to 45 degrees.
We check each wall with an angle gauge held on a straightedge. A corbeled wall steeper than 30 degrees, or a sloped wall past 45, is outside R1001.8.1, and parging over it smooths the surface without fixing the shape. That difference is written on the estimate in plain words. Steep corbeling matters beyond the code book, because every step it creates is a ledge where deposits settle.
Checking the draft after the repair
A smoke chamber repair is judged by how the fireplace draws. Once the cure allows, a small test fire, or smoke held at the opening, shows whether smoke now rises cleanly through the throat.
If smoke still spills, the chamber was not the only cause, and the estimate already said what else we saw, such as an undersized flue or a house that draws air down the chimney. We write down the result of the test either way. The test shows you as well as us that the fireplace now draws the way it should.
An undersized flue above a smooth chamber
R1003.15 ties the flue size to the fireplace opening: at least one tenth of the opening area for a square flue, one twelfth for a round one, and one eighth for a rectangular flue at a 2 to 1 ratio or more. A flue smaller than that can spill smoke however smooth the chamber is.
Flue and opening are both measured before chamber work is recommended, so you are not sold a parge coat to fix a sizing problem. The numbers go on the ticket either way. An undersized flue is a finding of its own, and the estimate explains its options, such as changes to the opening or to the flue.
Shape, walls, shelf and product, in writing
- Chamber height and opening width measured and written down
- Smoke shelf cleared, repaired and shaped to drain to the firebox
- Damper frame bedding checked and reset where loose
- Water entry at the top named and priced separately
Smoke chamber questions from Yulee
Why can't the sweep fix the smoke chamber?
A sweep cleans the surface that is there. Filling steps, resetting brick and troweling on refractory mortar is masonry work, and it is what makes the chamber smooth.
When can I light the fireplace after parging?
The refractory product's data sheet sets the cure time and how to bring it up to heat. We write both on your ticket with the date the work finished.
More services in Yulee
-
-
-
-
-
-
Smoke chamber repair from local masons in Yulee
Our masons measure the chamber, check the shelf and price the repair in Yulee before any work. Call (904) 920-5495.
Free Inspection