Chimney flue repair for Riverside homes
Book within 72 hours of the inspection, and your Riverside flue repair with our local crew takes 10% off.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local flue pros for Riverside chimneys
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Resurfacing systems are named with their listing, and installed by their instructions.
- Free inspection and estimateThe flue at your Riverside home is swept, examined from both ends and mapped at no charge.
- 100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
- Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.
A flue map, written by height
Our flue estimate reads like a map. Each defect is listed by flue, by height from the top or the firebox and by wall, with what it is: a crack, an open joint, a flaked face or a displaced tile.
Next to each entry is the repair and its price, and at the bottom is the flue size check against what the flue serves. That layout lets you see why a single repair path was chosen for the whole flue. Want a flue map for your chimney in Riverside? Call (904) 920-5495; the inspection that produces it is free.
The coastline lies beyond Riverside. Cummer Museum of Art and Gardens lies within Riverside.
Tile, joint, seal and size
- Cracked top tiles cut out and replaced from the roof
- Loose mortar ridges knocked back inside the flue
- Every defect written down by height
- Flue repair for fireplaces and appliance flues alike
How our flue pros repair a flue in Riverside
-
Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
-
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
-
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
-
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.
Settling chimneys and cracked tiles in Riverside
Horizontal cracks in flue tiles often follow movement of the chimney itself. The cause is the chimney and its footing, not the town.
In Riverside we check the outside of the chimney before repairing tiles cracked that way.
10% off any service booked within 72 hours of inspection
Cracked flue tiles? The repair you book any time in the 72 hours after your inspection is 10% off.
Flues that bend and the 30 degree limit
Leaning is allowed in a flue lining, within a limit. The code allows a slope no greater than 30 degrees from vertical. Beyond that, gases slow, deposits settle and the bend becomes hard to clean.
At an offset, tiles are cut on an angle and the joints are awkward to fill, so cracks and gaps cluster there. Repairs at a bend have limits too. Tools for resurfacing must pass the angle, and a replacement tile must be cut to match it. We note each offset's position and angle on the flue map, since it decides which repair can reach the damage.
How we examine a flue without opening it
Nearly all of a flue is out of reach, so it is examined from its ends. From the roof, we look down with a strong light. From the firebox or cleanout, we look up with a light and mirrors. The tiles are counted from the top, so every defect can be placed by height.
Where a stretch of flue cannot be seen from either end, we say so in writing. We do not guess at a section we could not see, and the estimate notes whether more access is needed before that part can be judged. Knowing what was and was not seen is part of an honest flue report.
One flue, several defects, one plan
Single faults are rare in a flue. A sweep might spot one crack while an open joint two tiles lower and a gap at the smoke chamber go unmentioned. Repairing them one at a time, with different methods, can cost more than one repair that covers them all.
So the plan is drawn for the whole flue. Each defect is listed, but the method is chosen to cover them together, whether that is resurfacing the full height, replacing the top two tiles and resurfacing below, or relining. The estimate shows how each defect is covered by the chosen method.
What goes on the flue map in Riverside
- Sweeping needed before the flue can be judged, listed on its own
- Relining priced when repair cannot give a sound, sized flue
- Waiting time before a fire, per the mortar or coat maker
- Fireplace or appliance use allowed before and after the repair
Before a flue repair is chosen
Do you repair chimney flues in Riverside?
Yes. We repair clay flues across Duval County, Riverside included, from single top tiles to full-height resurfacing. If a sweep left a note, have it ready when you call.
Does resurfacing make the flue smaller?
A little, because the coat adds thickness to every wall. We measure the flue and the fireplace opening first, and resurfacing is only offered when the flue will still meet the size the code asks for.
More services in Riverside
-
-
-
-
-
-
Learn more about chimney flue repairAll services in Riverside
A flue that carries the smoke out of your Riverside home
Not sure what shape your Riverside flue is in? The inspection is free, and the repair is 10% off if you book it within 72 hours.
Free Inspection