Stone veneer chimney repair for Riverside homes
Our Riverside masons match the joint style as carefully as the mortar color.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Stone repair experts who identify the build first
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The joint style is matched so the repair does not stand out.
- Free inspection and estimateWhether your Riverside chimney is full stone or veneer is settled on a free visit, before any price.
- Upfront pricing, no hidden feesStones, joints and veneer area are priced in writing one line at a time.
- Family owned and operatedOur family-owned masons approve the mortar sample with you before the first joint is filled.
A stone base with brick or stucco above
Some chimneys change material partway up: stone at the base, then brick or stucco above the roof. Each material has its own repair, and the joint between them is a place where water gets in if the detail was never flashed or sealed. Each material also expands and dries differently, which puts stress on the line where they meet.
We check each part of a mixed chimney in Riverside with the method it needs and look closely at where they meet. The estimate lists each material's work on its own line so nothing is lost between them.
The county for Riverside is Duval County. Riverside sits away from the coastline.
Stone chimney repairs we handle in Riverside
- Loose adhered veneer taken off and reinstalled
- Dry-stack veneer refitted tight
- Stone cleaned by tested, gentle methods
- Your Riverside chimney's build identified before pricing
From the first loose stone to the last tooled joint in Riverside
-
Describe what moved
Tell us what has shifted or fallen, and the free visit comes equipped for it.
-
Build and backing confirmed
Corners, joints and the base show the build, and a loose piece shows what is behind the veneer.
-
Reset, repoint or reinstall
Stones go back on fresh beds, joints fill in layers, and veneer returns to a repaired backing.
-
Matched and cured
An approved mortar sample and the old joint profile guide the finish, and the cure time is written down.
Veneer drainage inland in Riverside
Water behind adhered veneer has to drain out at the base whether the chimney is inland or on the coast. In Riverside, a buried base or a missing screed traps it all the same.
Blocked exits at the base of veneer chimneys in Riverside are opened as part of the repair.
10% off any service booked within 72 hours of inspection
Say yes to the stone work within 72 hours of the inspection and save 10%.
The drainage exit at the base
Water that gets behind adhered veneer is meant to run down the barrier and out at the base, through the screed or flashing R703.12 calls for. That exit only works if it is open to the air, with a gap above soil, mulch and paving.
Every veneer chimney's base is checked for a working exit. Where it is buried or missing, the estimate covers opening it up or adding the detail, which can mean removing the lowest course of stone. Where a patio or step has been built up against the base, the exit may need to be recreated above the new grade.
The cap on top of a stone chimney
The top of a stone chimney follows R1003.9.1 like any masonry chimney: a cap of concrete, metal or stone that slopes water away, overhangs to a drip, and meets the flue liner at a sealed joint that lets the two move apart. A flat mortar wash across the top stones meets none of that.
Water that leaves the top the wrong way runs down the stone and into the joints below. We check the cap on every stone chimney we work on and price crown work separately, in the order that keeps the new stone work dry. A stone cap made from a single slab or a few large pieces also needs a drip edge cut or formed underneath it.
Removing hard cement patches
Portland cement patches spread over stone joints are harder and less permeable than the stone or the original mortar. Moisture that cannot leave through the patch leaves through the stone, and hard patches can crack the stone edges they cover.
Taking them out is slow work, done by hand along the joint so the stone edge survives. We price the removal separately from the repointing, because a chimney with a lot of old patching takes longer before any new mortar goes in. Where a patch has already cracked a stone edge, that stone is reset or replaced along with the joint.
Stone, joints, backing and base, in writing
- Mortar mix and sand matched, with a cured sample to approve
- Joint profile matched to the existing work
- Veneer gap above the roof corrected to the maker's guide
- Structural movement flagged ahead of any stone work
Stone chimney questions from Riverside
Can you match my stone?
We look for the closest current match and also consider moving stones from a hidden face to the repair. You see the options and approve a sample before any stone is removed.
Do you repair manufactured stone veneer as well as natural stone?
Yes. Manufactured veneer follows its maker's installation guide for the backing and setting mortar, and we match the product line and color as closely as it allows.
More services in Riverside
-
-
-
-
-
-
Learn more about stone chimney repairAll services in Riverside
Loose stones or failing veneer in Riverside?
Say what has shifted or fallen when you call (904) 920-5495, and we book the free look in Riverside.
Free Inspection