Local gas fireplace installation for Panama Park homes
Gas supply and wiring for your Panama Park install are named with the trade that does them on a free planning visit.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Gas fireplace installation specialists who vent to the manual
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The permit and its inspections are on the schedule, and the finish waits until they pass.
- Family owned and operatedOne family business frames, vents and starts up the unit in Panama Park, and lines up the gas and electrical trades.
- Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.
When a log set or an insert suits better
An existing wood-burning fireplace in a house in Panama Park changes the question. A gas log set can go into a sound masonry firebox and vent through the existing chimney, and a sealed gas insert can slide into it with a vent run up the old chimney. Gas log installation and gas fireplace insert installation are separate jobs we also do.
Before recommending a new built-in unit, we look at the fireplace you already have, because using it can mean no new wall opening and no new termination. We tell you which of the three makes sense for the room, and why. On the free planning visit in Panama Park we check where a vent can exit; call (904) 920-5495.
Within Jacksonville city limits, Panama Park is its own named neighborhood. Panama Park falls within Duval County.
From vent exit to first burn
- Vent route drawn and checked against the vent table
- Siding standoff fitted behind a wall termination
- Wiring for the receiver and blower run before the wall closes
- Walk-through of your new Panama Park unit and its manual
How our gas fireplace pros install a unit in Panama Park
-
Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
-
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
-
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
-
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.
Bedrooms and B-vent units in Panama Park
A B-vent fireplace takes its air from the room, so the fuel gas code limits it in bedrooms to rooms of a set size. A sealed direct-vent unit avoids that limit.
We check the room size in your Panama Park home before recommending either type.
10% off any service booked within 72 hours of inspection
From the vent run to the start-up checks, a gas fireplace install in Panama Park is 10% off.
Pipe inside a pipe
Direct-vent pipe is coaxial: an inner pipe carries exhaust out, and the space between it and the outer pipe carries fresh air in. The two streams run side by side all the way to the termination, which has openings for both. Because the incoming air surrounds the hot inner pipe, the outer wall stays cooler than a single-wall vent would, and that is part of why the listed clearances to framing are small. The pipe, its joints and its termination are one listed system from the vent maker the manual names, and parts from another system are not mixed in.
A vertical termination through the roof
When the vent goes up instead of out, it climbs up past the ceiling and across the attic to a vertical cap, which stands as high above the roof as the manual requires for that roof pitch. The penetration is sealed with the roof flashing and storm collar that come in the vent kit, fitted as its instructions show. Around them, the roof covering itself may need sealing and patching, and we name the trade that does it. In the attic, the pipe keeps its listed clearance to framing and insulation, with the shield the vent maker supplies.
Sizing the supply to the input
Full rated input, at the pressure on the rating plate, is what the burner needs, measured at the valve with the burner running. The supply line from the meter or tank has to deliver that while the water heater, range and any furnace run too. Sizing that line is the gas contractor's job, done to the fuel gas code's tables, and it may mean a larger line or a new branch rather than a tap off the nearest pipe.
At start-up the inlet reading tells whether the supply did its job. A low inlet reading at start-up goes back to the gas contractor instead of into an adjustment at the valve.
Checked outside and in before an install in Panama Park
- Termination spot measured to windows, soffits, corners and walks
- Roof covering around a roof termination, and who patches it
- Service access panels left removable after the finish
- Inlet and manifold pressures read and recorded at start-up
Before the vent hole is cut
Will the vent termination be visible outside?
Yes, a wall termination is a cap on the outside wall at the spot the clearances allow. If the house is under an association, check its rules before the spot is final.
Can I choose the tile or stone around the fireplace?
Yes, within the manual's rules. Only noncombustible materials may cover the metal face, set with the adhesive rating the manual gives, and a mantel follows the manual's chart.
More services in Panama Park
-
-
-
-
-
-
Learn more about gas fireplace installationAll services in Panama Park
A vented gas fireplace for your Panama Park room
Room with no chimney in Panama Park? Our local specialists check where a vent can go at no charge.
Free Inspection