Family-run chimney tuckpointing in Panama Park
A free survey of every face in Panama Park, same day if the calendar allows, and 10% off repointing you book within 72 hours.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Masons who survey every face first
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Water getting into the chimney from above is priced with the repointing, so new joints start dry.
- Free inspection and estimateEvery face of your Panama Park chimney is scratch-tested and sketched at no charge.
- 100% satisfaction guaranteedIf the new joints are not sound, full and matched as agreed, we come back and fix them.
- Family owned and operatedA family masonry crew does the survey and the work, so the person who priced a face is the one who repoints it.
A chimney that looks fine from below
Plenty of worn joints are invisible from the ground. The top courses and the side facing away from the street are where mortar goes first, and neither is easy to see from a driveway. A missing crumb of mortar today can be an open joint by next season.
A close look from the roof tells the real story. We check every face at arm's length and write down what we find, including the joints that are sound. Never had your Panama Park chimney's mortar looked at up close? Call (904) 920-5495 and book a free inspection with our masonry team.
Panama Park sits in Duval County. Panama Park does not reach the coast.
Raked, filled, tooled and cured
- Mortar type chosen to suit the brick
- Old caulk and skim patches cut out
- Fresh work shaded, misted and covered from rain
- Roof and yard protected, debris cleaned up
From the scratch test to cured joints in Panama Park
-
Every face surveyed
Joints are scratch-tested at several heights and the failed courses marked on a sketch.
-
Joints raked and cleaned
Old mortar comes out to sound depth, head joints by hand, then joints are cleaned and dampened.
-
Filled in layers and tooled
Matched mortar goes in stage by stage, then is tooled to the original profile.
-
Cured and cleaned up
Fresh joints are protected while they cure, the faces brushed and the roof cleared.
Joints that pass through the attic in Panama Park
Interior chimney joints are sheltered from rain, yet they still age and can open up beside the framing.
If the chimney runs through your Panama Park attic, we check its joints there as part of the survey.
10% off any service booked within 72 hours of inspection
Repointing earns the discount whether or not you have used our masons before.
Why head joints are cut by hand
The short vertical joints between bricks in a course are the head joints. They are narrow and short, and a grinder blade that slips there cuts into the brick on either side, leaving a scar that shows long after the job.
Preservation Brief 2 advises against power tools on head joints for that reason. We cut them by hand with a plugging chisel, which is slower but leaves the brick edges intact. The time that takes is part of why a repointing quote is priced by the joint, not by the square foot of wall.
Filling deep joints in stages
A deep joint is not filled in one push. Preservation Brief 2 has it filled in layers, and a layer should resist a thumbprint before another is packed on top. A single thick fill can shrink and crack away from the brick.
We pack each layer firmly with a pointing tool so there are no voids behind it, then add the next when the first will take a thumbprint without smearing. The last layer is brought flush with the face for tooling. It takes longer than filling in one pass, and it is the step that makes a repointed joint last.
Why new mortar is softer than the brick
Preservation Brief 2 wants new pointing mortar weaker than the brick and more open to vapor. Mortar is meant to be the part that gives, taking up movement and letting moisture leave the wall through the joints.
Mortar stronger than its brick sends those stresses and that moisture through the brick instead, and the brick edges and faces start to break down. So the strongest mortar is not the best choice for every chimney. We check the brick first and choose a mortar that suits it, then write the type down.
Joint findings written down before pricing
- Faces and courses needing repointing, marked on a sketch of the chimney
- Raking depth for each face, set by joint width
- Head joints cut by hand, and where a grinder is used
- Caulk or skim patches to remove before repointing
Repointing questions from Panama Park
Can you repoint just part of the chimney?
Yes, when the rest is sound. We scratch-test every face, and the quote covers only the courses and faces that need it, with the others noted as tested and sound.
Which mortar will you use?
A type from ASTM C270 picked for your brick and its exposure, normally weaker than the brick itself, in line with preservation guidance. The type is written on the estimate.
More services in Panama Park
-
-
-
-
-
-
Learn more about chimney tuckpointingAll services in Panama Park
Book a joint survey before the next storm
Our masons test the joints on all sides of your Panama Park chimney and put a written price on each. Call (904) 920-5495.
Free Inspection