Local gas fireplace installation in Palm Valley

Heater or decorative, the Palm Valley unit is chosen from its listing and the room it has to suit, at a free inspection by local pros.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Gas fireplace installation specialists who vent to the manual

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Every clearance comes from the unit's manual, from the header height to the mantel depth.

Family owned and operatedOne family business frames, vents and starts up the unit in Palm Valley, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

Traffic, drafts and furniture around the unit

The manuals say where not to put a gas fireplace as clearly as where to put it. They rule out high-traffic spots and windy or drafty areas, and they set a distance in front of and beside the unit that furniture, curtains and other flammable items have to keep. In a room in Palm Valley, that means looking at the doorways people walk through, ceiling fans and supply registers that blow across the opening, and where the sofa will end up. We mark the unit's position and its clear space on the floor before framing, so the room still works once the fireplace is in. We plan gas fireplace installs in Palm Valley on a first visit that costs nothing; call (904) 920-5495.

Palm Valley runs along the Intracoastal Waterway. The county for Palm Valley is St. Johns County.

Gas fireplace installs around Palm Valley

Vent route drawn and checked against the vent table
Horizontal runs pitched the way the manual asks
Enclosure and header framed to the manual's drawing
Permit and inspections for your Palm Valley install scheduled

Call (904) 920-5495 Free Inspection

Vent out, frame, wire, start up

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

Keeping the termination reachable

Near the water, a vent cap benefits from an occasional rinse and a look. A termination placed high under an eave is hard to reach for either.

Within the manual's clearances, we place terminations in Palm Valley where they can be checked from the ground.

10% off any service booked within 72 hours of inspection

Settling on a model for a room in Palm Valley takes time, and the 72 hours give you some.

Call (904) 920-5495 Free Inspection

Reading the vent table

Each direct-vent manual we work from carries a vent table or chart that ties the vertical rise to the horizontal run. A unit that exits straight through the wall may allow only a short horizontal run; one that rises several feet first may allow a longer run after the rise. Each elbow counts against the total as a set length of straight pipe.

A route outside the table can pull too little air in or push exhaust back, so the burner misbehaves or the pilot drops. We draw the route, add up each length and elbow, and check the total against the table before cutting.

Reading the mantel chart

A combustible mantel above a gas fireplace follows a chart in the manual that pairs the mantel's depth with the minimum height above the opening. The deeper the shelf, the higher it has to sit. Trim that stands out from the facing beyond a small set distance is treated as a mantel under the chart, so a thick molding counts.

Some makers offer mantel packages already tested for their units. We mark the chart height on the framing so blocking goes in at the right level, and check the mantel you choose against it. The chart says where its measurements start, and we measure from the same point.

Choosing termination parts near salt spray

Salt spray speeds up corrosion of exposed steel, and a new vent termination spends its life outdoors. Near the coast, we look at what the vent maker offers for the termination, its trim and its fasteners, including stainless or coated options where the maker lists them, and use those parts on the exterior. The termination is placed where it can be reached for rinsing and inspection, and the manual's clearances still govern its spot. The corrosion-resistant parts chosen are recorded, so they can be matched if anything is replaced later. Rinsing the cap with fresh water now and then slows the salt down.

Unit, vent route and trades on paper

Unit named by maker and model, with its heater or decorative listing
Wall thimble or roof parts from the vent maker's list
Every connection leak-checked with solution before handover
Barrier screen fitted and logs set to the placement diagram

Gas fireplace install questions from Palm Valley

Do you run the gas line to the new fireplace?

No. The line to the unit's shutoff valve is a gas contractor's job, or the propane supplier's on a propane system. The estimate says who and when, and start-up follows once gas reaches the valve.

Is a permit needed for a gas fireplace?

Yes. The permit comes from the local building department, and its inspections cover the gas connection, the vent and the framing before the finish closes them in. Both appear on the estimate.