Family-owned top damper installation in Ortega
We measure your flue tile in Ortega before ordering, so the damper we bring is made for that tile.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Damper experts who measure before they order
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The handle goes where you can see it before every fire.
- Free inspection and estimateYour flue tile in Ortega is measured and the crown checked on a free visit before any damper is ordered.
- Upfront pricing, no hidden feesThe model, the handle position and any tile or crown work are priced in writing up front.
- 100% satisfaction guaranteedIf the lid does not seal or open the way we showed you, we return and adjust it.
A throat damper rusted in place
The plate damper just above a masonry firebox sits where heat, soot and water all reach it, and over time it rusts to its frame. Some stick shut, some stick open, and some move but no longer close tight. Freeing one that has rusted thin may buy little time. A rusted plate can also drop without warning if its pivot fails.
In Ortega, we check whether the throat damper is worth saving, and where it is not, fit a top sealing damper at the flue tile instead. The old plate is removed or fixed open, and both steps are priced on one estimate after a free inspection.
Ortega is a neighborhood within the City of Jacksonville. The county for Ortega is Duval County.
From the tile measurement to the handle
- Top sealing dampers set in the maker's adhesive
- Every flue identified before any fitting
- Your Ortega chimney's tile and crown checked first
- Make and model of your Ortega damper written down
Measure, order, set, adjust
-
Tile measured on the roof
The flue tile's outside size, height and rim are checked on a free visit, with the crown around it.
-
Model ordered to fit
The damper is chosen from the maker's size chart for your tile and approved on the estimate first.
-
Frame set, cable run
The frame is set in the maker's adhesive, the old plate made safe and the cable run to the handle.
-
Adjusted and demonstrated
The lid is adjusted to seal, and you try the handle before we leave, with the cure time written down.
Rain down an inland flue in Ortega
An inland chimney in Ortega still takes rain at its top. Without a cap or a closed damper, that rain reaches the smoke shelf and rusts the throat damper.
Closing the damper between fires keeps the flue dry.
10% off any service booked within 72 hours of inspection
Sized to the flue tile it seals, a top damper in Ortega is 10% off.
Measuring the flue tile
Top dampers are sized to the outside dimensions of the flue tile, since the frame sits over or on its top edge. Clay tiles come in several square and rectangular sizes, and round flues need a model made for round openings.
On the roof, the tile's outside dimensions are measured and its top edge checked for level and soundness. The model is chosen from that measurement and the maker's size chart, and both go on the estimate. A multi-flue chimney is measured flue by flue, since tiles on the same chimney can differ in size.
Why an open flue loses conditioned air
A chimney is a tall column connected to the room at the bottom and the outdoors at the top. When the air inside the house and the air outside differ in temperature, air moves through that column, in or out depending on conditions.
Leaky throat dampers let that movement continue between fires. A gasketed lid at the top stops it, and it seals the whole flue rather than just the throat. We explain what to expect in your house, without promising a figure. The effect depends on the house, the chimney and how the fireplace is used, which is why we describe it rather than put a number on it.
Chimneys with more than one flue
On a chimney with several flues, each fireplace flue gets its own top damper and each appliance flue keeps its own cap. Flues of different heights, or flues set close together, affect which damper models fit.
We measure each flue and check the spacing between them before choosing models. Where a multi-flue cap already covers the top, we explain whether it has to be modified or replaced to make room for the damper. A drawing of the chimney top with each flue labeled goes on the estimate.
Tile, crown, throat and model, in writing
- Tile rim and crown checked, with any repair priced first
- Cable routed clear of tile joints and old damper edges
- Existing top damper serviced with the maker's parts
- Make, model and flue size written down for your records
Top damper questions from Ortega
Can you fit a top damper the same day in Ortega?
The measurement can happen the same day when the schedule has room, but the damper is ordered to fit your tile. We install it once it arrives, and the adhesive then needs its set time.
What happens to my old damper?
It is removed or fixed fully open so it cannot close across the flue. The ticket records which.
More services in Ortega
-
-
-
-
-
-
Learn more about top-sealing damper installationAll services in Ortega
Seal the flue where it ends
Describe what the throat damper does when you call (904) 920-5495, and we set up the free visit in Ortega.
Free Inspection