Local stone chimney repair in Ortega
Deep stone joints get filled in layers, not smeared over. That is how Ortega stone repairs are done right.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Stone chimney specialists for Ortega homes
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
A cured sample is approved before repointing starts on your Ortega chimney.
- Free inspection and estimateWhether your Ortega chimney is full stone or veneer is settled on a free visit, before any price.
- Upfront pricing, no hidden feesStones, joints and veneer area are priced in writing one line at a time.
- Family owned and operatedOur family-owned masons approve the mortar sample with you before the first joint is filled.
Stains running down from the top
Dark or white streaks starting just below the top of a stone chimney mean water is leaving the crown and running down the stone instead of dripping clear. A crown without an overhang and a drip edge sends every rain across the top courses. The staining also marks the courses most likely to need repointing first.
On a stone chimney in Ortega, we check the crown's slope, overhang and drip edge along with the top courses of stone. Crown work and stone work are priced separately, and the order is set so the new stone is not stained again.
Ortega falls within Duval County. Ortega lies inland.
What our stone masons fix in Ortega
- Deep stone joints raked and repointed in layers
- Loose adhered veneer taken off and reinstalled
- Veneer cut back from the roof surface
- Your Ortega chimney's build identified before pricing
How our masons repair a stone chimney in Ortega
-
Describe what moved
Tell us what has shifted or fallen, and the free visit comes equipped for it.
-
Build and backing confirmed
Corners, joints and the base show the build, and a loose piece shows what is behind the veneer.
-
Reset, repoint or reinstall
Stones go back on fresh beds, joints fill in layers, and veneer returns to a repaired backing.
-
Matched and cured
An approved mortar sample and the old joint profile guide the finish, and the cure time is written down.
Mortar hardness inland in Ortega
The rule that mortar should be no harder than the stone holds in Ortega as it does everywhere. Hard patches on soft stone crack the edges whatever the distance from the coast.
We match the mix to your stone and write it on the ticket.
10% off any service booked within 72 hours of inspection
Stone work keeps our workmanship warranty when the 10% comes off.
Matching mortar strength to the stone
Repointing mortar should be no harder than the stone around it. When mortar is stronger and less permeable than the stone, stress and moisture move through the stone instead of the joint, and the stone edges crack or flake. Dense, hard stone tolerates a stronger mix, while soft, porous stone needs a weaker one.
We identify the stone before choosing the mix, using ASTM C270 mortar types as the starting point and adjusting for softer stone. The mix goes on the ticket so any later repair uses the same thing. Where an earlier repair used a harder mortar than the stone can live with, those joints are cut out and redone rather than matched.
Taking veneer off and putting it back
When a section of veneer has lost its backing, the fix is to take that section off, repair the water barrier and lath, and set the stones back. Pieces are numbered as they come off where the pattern matters, cleaned of old mortar and reset with the setting mortar their maker specifies, buttered over the whole back.
The edges of the repaired area are feathered into the sound veneer so the joints run through. We price the area in square feet and say how many stones we expect to reuse, since breakage during removal is part of the job. New lath and barrier are lapped into the old ones at the edges of the opening, so water keeps draining the right way.
Where veneer meets the roof
Veneer installation guides call for a gap between the bottom of the stone and the roof surface, with flashing and the water barrier lapped so water drains out over the roofing. Stone set tight to the shingles pulls water up into the veneer, and the base of the stone stays wet.
The gap and the flashing detail come from the veneer maker's guide for the product on your chimney. Where the stone sits on the roof, we cut it back and correct the detail, and flashing work is priced on its own line. Cutting stone back at the roof is done with care for the roofing below, which is protected before any saw is used.
What we check on a stone chimney in Ortega
- Loose stones counted, reset on fresh beds and repointed
- Joint profile matched to the existing work
- Base drainage exit checked and opened where buried
- Old cement patches and caulk cut out before repointing
Before a stone is taken out
Do you charge to look at a stone chimney in Ortega?
No. The stone, the joints, the top and the base are all checked, and the written estimate costs you nothing.
What happens if a reset stone in Ortega works loose?
Our satisfaction guarantee covers the stone work we quote. If a stone we reset works loose or the joints we filled fail, we return and redo them.
More services in Ortega
-
-
-
-
-
-
A free stone chimney check in Ortega
Our family-owned masons repair stone chimneys in Ortega and guarantee the work to your 100% satisfaction.
Free Inspection