Local chimney flue repair in Ortega
Repair or reline? For the flue in your Ortega home, we tell you plainly which one the tiles allow.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Flue specialists who map before they repair
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Water getting into the flue is traced and fixed with the repair, not left for later.
- Free inspection and estimateThe flue at your Ortega home is swept, examined from both ends and mapped at no charge.
- 100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
- Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.
A cleanout door at the base
Chimneys that vent an appliance usually have a cleanout near the base, a small metal door that gives access to the bottom of the flue. The code puts it within 6 inches of the base and asks for a noncombustible cover.
A rusted or missing door leaks air into the flue and lets debris spill out. It is also where the bottom of the flue can be seen during a repair. We check it on every flue job and price a new door when it no longer closes. Cleanout door missing on your chimney in Ortega? Call (904) 920-5495 and book a free inspection.
Ortega is a neighborhood within the City of Jacksonville. The county for Ortega is Duval County.
Flue repairs we handle in Ortega
- Seal around the top tile remade
- Loose mortar ridges knocked back inside the flue
- Every defect written down by height
- A written flue plan for your Ortega chimney, free of charge
Sweep, map, repair, check
-
Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
-
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
-
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
-
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.
Yearly checks for repaired flues in Ortega
A repaired flue still gets the yearly NFPA 211 inspection like any other.
At that check in Ortega, we look again at the repaired tiles and joints to confirm they have held.
10% off any service booked within 72 hours of inspection
Flue repair earns the 10% off even if you have booked with us before.
Clay flue tile and its standard
Clay flue lining is made to ASTM C315, one of the lining types the code lists for masonry chimneys. The tiles are fired clay sections, round, square or rectangular, stacked one on another up the chimney.
Replacement tiles are matched by their outside and inside dimensions, because a new section has to sit on the one below and line up on the inside. Where a tile size is no longer made, the repair above that point may need a different approach. We measure the existing tile before ordering, and the size goes on the estimate so the part is not a guess.
Replacing the top flue tile from the roof
The top tile is the one flue section that can be reached without taking the chimney apart. When it is cracked or broken, the concrete around it is cut back, the old section lifted out and a new tile set in refractory mortar on the one below.
The new tile has to line up on the inside and stand above the chimney top. Then the seal around it is remade so water sheds rather than soaking in. Repairs lower down cannot be reached this way, which is why top tile replacement suits damage confined to the last section or two.
Cleanouts and the bottom of the flue
Under R1003.17, a masonry chimney venting an appliance gets a cleanout near the bottom of each flue: no more than 6 inches up from the base, at least 6 inches tall, closed by a noncombustible cover, with its top edge 6 inches or more under the lowest inlet. Flues serving fireplaces can be cleaned through the fireplace instead.
The cleanout is also a window into the bottom of the flue. Debris piled there, broken tile among it, tells us damage has fallen from above. A rusted door that no longer closes lets air in, which affects draft. Both are small items, and we list them on the flue estimate rather than leaving them for later.
Flue findings written down before pricing
- Sweeping needed before the flue can be judged, listed on its own
- Resurfacing system named with its UL 1777 listing, where one is used
- Water entry at the cap and bond break priced alongside
- Fireplace or appliance use allowed before and after the repair
Flue repair questions from Ortega
Does resurfacing make the flue smaller?
A little, because the coat adds thickness to every wall. We measure the flue and the fireplace opening first, and resurfacing is only offered when the flue will still meet the size the code asks for.
Is flue repair cheaper than relining?
When the damage suits a repair, it is usually the smaller job. When it does not, stacking repairs on a failing flue costs more in the end, and we price relining instead so you can compare.
More services in Ortega
-
-
-
-
-
-
Repair cracked flue tiles in Ortega
One top tile or the full height, each flue repair in Ortega gets a written price before work begins.
Free Inspection