Chimney crown repair in Oakleaf Plantation by local masons

Slope, overhang, drip edge, reinforcement and bond break are checked on every Oakleaf Plantation crown, and that inspection is free of charge.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Chimney crown pros who check before they seal or recast

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

A cap that has to come off for a recast goes back on with fasteners that suit the new crown.

Free inspection and estimateWe map the cracks on your Oakleaf Plantation crown and check the brick under it at no charge.
Upfront pricing, no hidden feesCoating and recasting are both priced on paper, so you see the difference before choosing.
100% satisfaction guaranteedIf the finished crown is not right, tell us and we come back to put it right.

Call (904) 920-5495 Free Inspection

Starting with what is actually up there

The first job on a crown call in Oakleaf Plantation is finding out what the top of the chimney actually is. It may be a mortar wash troweled around the flue, a concrete crown cast in place, or a precast slab set on a mortar bed. From the roof we can tell which, and the answer shapes everything that follows.

A wash and a cast crown fail differently and are repaired differently. So the first line of the estimate names the type, the second maps the cracks, and only then does it propose a coating, a patch or a new crown. Cracks on top of the chimney in Oakleaf Plantation? Our masons tell you coat or recast after one look, so call (904) 920-5495.

The coastline lies beyond Oakleaf Plantation. Oakleaf Plantation falls within Clay County.

Crown repair jobs we handle in Oakleaf Plantation

Wider cracks filled before a crown coating goes on
Bond break sealed around each flue tile
Crown sloped so water runs off toward the edges
Chimney cap refastened once the new crown can hold it

Call (904) 920-5495 Free Inspection

How crown repair runs

Crack map from the roof
We identify the type of top and sketch each crack with its width, so the choice between coating and recasting is based on what is there.
Prep for coating or removal
A sound crown is cleaned and its wider cracks filled; a failed one is broken out down to sound brick.
Coat, or form and pour
The coating is brushed on in dry weather, or new concrete goes into forms with an overhang, a drip groove and reinforcement.
Cure, seal and refit the cap
The bond break at each flue is sealed, the concrete cures under cover, and the cap goes back on.

Crowns around two or more flues in Oakleaf Plantation

A crown over several flues has to drain between the tiles as well as off the outside edges. A flat patch between two tiles holds water against both.

Recasts in Oakleaf Plantation are sloped away from every tile, and each tile gets its own sealed bond break.

10% off any service booked within 72 hours of inspection

Seal or recast, crown repair in Oakleaf Plantation earns the 10% discount.

Call (904) 920-5495 Free Inspection

Mapping the cracks before choosing a repair

Before we propose anything, the cracks on a crown are mapped: where each one starts, where it runs, and how wide it is along its length. A sketch shows them. The pattern matters as much for the diagnosis as the width does.

Cracks radiating from the flue corners point to the tile pushing on the crown. A crack running parallel to an edge, a short way in, points to a feathered edge breaking off. A web of fine cracks across the whole surface points to shrinkage in the original pour. Each pattern leads to a different repair, which is why the map comes first.

Taping the flue tile before a coating

Before a crown is coated, tape goes around each flue tile, set a little higher than the crown surface. The coating is brushed up to that line, over the tile-to-crown joint, and ends in a clean edge instead of a ragged smear.

What sits in the joint where the tile meets the crown matters more than the tape. The bond break the code asks for is a flexible, caulked joint that lets the tile expand as it heats while the concrete stays put. Rigid patching cement packed into it locks the tile to the crown, and the next fire cracks one or the other. An open joint at the tile is cleaned out and resealed with a flexible sealant before the coating goes on.

Keeping new concrete damp while it cures

Concrete gains strength through a chemical reaction that needs water, and a crown on a sunny, breezy roof dries out fast. If the surface dries too early, it can craze and dust, and the crown ends up weaker than its mix should give.

After the pour, the crown is covered and kept damp for the curing period the mix calls for, and it is protected from rain until it has set. The forms come off once the concrete can hold its edges. Those steps are why a crown recast can take more than one visit, and you know in advance when each one happens.

Measured on the crown in Oakleaf Plantation before pricing

Top courses of brick relaid before the new crown goes on
Overhang, drip groove and slope for the new crown
Chimney cap removal and reinstallation, with how it is fastened
Debris removal from the roof and gutters after the work

Before your crown is coated or recast

Can I tell from the ground whether my crown is a mortar wash?

Sometimes. A thin gray layer that tapers to the edge with no overhang is likely a wash, while a thicker slab that projects past the brick is likely a cast crown. We confirm it from the roof.

Does crown work mean the chimney cap comes off?

For a recast, yes. For a coating, it depends on how the cap is mounted. The estimate says which applies to your chimney.