Tuckpointing chimneys in Nocatee by local masons
A free survey of every face in Nocatee, same day if the calendar allows, and 10% off repointing you book within 72 hours.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local repointing pros for Nocatee chimneys
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Water getting into the chimney from above is priced with the repointing, so new joints start dry.
- Free inspection and estimateEvery face of your Nocatee chimney is scratch-tested and sketched at no charge.
- 100% satisfaction guaranteedIf the new joints are not sound, full and matched as agreed, we come back and fix them.
- Family owned and operatedA family masonry crew does the survey and the work, so the person who priced a face is the one who repoints it.
Hard gray mortar next to soft brick
Old chimneys were often laid in softer mortar than today's strong mixes. When a later repair filled the joints with hard gray mortar, the stress of movement and drying can shift into the brick instead, and the brick edges beside the new joints start to crumble.
Repointing an older chimney means choosing a mortar softer than its brick, as preservation guidance advises. We check the brick and the old mortar before picking a type. Crumbling brick edges beside newer joints in Nocatee? Phone (904) 920-5495, and our family masons will look at it for free.
The county for Nocatee is St. Johns County. At the 2020 Census, Nocatee was home to 22,503 people.
What chimney tuckpointing covers in Nocatee
- Every face scratch-tested and sketched
- Joints cleaned and dampened before filling
- Deep joints filled in layers, not one pass
- Fresh work shaded, misted and covered from rain
From the scratch test to cured joints in Nocatee
-
Every face surveyed
Joints are scratch-tested at several heights and the failed courses marked on a sketch.
-
Joints raked and cleaned
Old mortar comes out to sound depth, head joints by hand, then joints are cleaned and dampened.
-
Filled in layers and tooled
Matched mortar goes in stage by stage, then is tooled to the original profile.
-
Cured and cleaned up
Fresh joints are protected while they cure, the faces brushed and the roof cleared.
Chimney joints a few miles from the coast
Storms near the ocean drive rain hard at chimney faces in Nocatee, only a few miles inshore. The faces that take the weather wear their joints first.
We survey those sides closely on Nocatee chimneys and price them on their own.
10% off any service booked within 72 hours of inspection
Sandy joints? Book the repointing within 72 hours of the survey and 10% comes off.
Where a grinder helps and where it harms
On long bed joints between courses, a grinder can open the joint quickly, provided the joint is wide enough for the blade and the mason is steady. The danger is the brick edges, which a wandering blade chips or widens.
We use a grinder only where the joint width allows it, keep the cut inside the old mortar and finish by hand to square the joint. On older, softer brick, or where joints are thin, the whole job is done by hand. The method for each face is written on the estimate so there is no surprise about what tools come up the ladder.
Tooling the joint to shed water
Once the final layer has firmed, the joint is tooled: pressed and shaped with a jointer to compact the surface and match the profile of the old joints. Tooling closes tiny gaps at the brick edge where water could enter.
For exterior walls, the Brick Industry Association's water penetration note prefers concave and V profiles made with a jointer, since tooling compacts the mortar and the shape sheds rain. Where the original joints are a different profile, we match them so the wall reads as one. The profile used is written on the estimate. A joint tooled too early smears, and one tooled too late crumbles at the edge, so timing is watched face by face.
What white deposits say about the joints
Efflorescence is the white crust salts leave when water carries them to the surface of masonry and evaporates. It appears on brick and joints wherever water is moving through the wall.
It tells us water is present, not where it entered. Open joints are one source, and so are the chimney top and the roof line. We brush a patch clean to see the joints beneath and follow the pattern of deposits to the likely entry points. The crust itself is cleaned off after the water is stopped, since cleaning it earlier only lets it return.
Joint findings written down before pricing
- Raking depth for each face, set by joint width
- Mortar type under ASTM C270 and the reason for it
- Loose top courses that need relaying rather than repointing
- Weather protection and curing for the new joints
Repointing questions from Nocatee
How close will the new mortar color be?
A sample batch is mixed, cured beside your brick and checked in daylight before any joint is filled. New joints can still look slightly fresher at first, and we show you the sample so you know what to expect.
What if you find loose bricks while raking?
We stop and show you. A loose brick or course needs relaying or replacement, which is priced as its own item before we continue.
More services in Nocatee
-
-
-
-
-
-
Learn more about chimney tuckpointingAll services in Nocatee
Book a joint survey before the next storm
Our masons test the joints on all sides of your Nocatee chimney and put a written price on each. Call (904) 920-5495.
Free Inspection