Local chimney cap replacement in Nocatee

Caps for Nocatee flues serving fireplaces and other appliances, matched during a free inspection to what each flue carries.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Chimney cap specialists who measure in Nocatee first

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

We fit caps in Nocatee ourselves, from the tape measure on the tile to the last screw.

Free inspection and estimateWe measure every flue on your Nocatee chimney at no charge before any cap is ordered.
Upfront pricing, no hidden feesThe cap model, its metal and the fastening are priced together, so the total is clear.
Workmanship warrantyOur fitting and fastening carry the workmanship warranty, with the cap maker's terms in writing.

Call (904) 920-5495 Free Inspection

Capping a flue after birds or animals

Scratching above the damper, chirping in the chimney, or twigs dropping into the firebox mean something has found the flue. A cap is how that stops happening again, but the cap goes on last. Swifts that nest in chimneys are federally protected, so an active swift nest stays until the birds have moved on for the season. Other animals come out first, the nest material and droppings are cleared from the shelf, and only then does the new screen close the opening. That order holds for every Nocatee home, so nobody ends up capping an animal inside the flue. Pick a time for our cap pros to come to Nocatee; the number is (904) 920-5495.

The coast is close to Nocatee. Nocatee lies within St. Johns County.

Cap replacement work for Nocatee homes

Tile height above the crown checked for a secure fit
Slip-in, band-mount or full-crown style picked to suit the tile
Screen openings checked against Florida code R1003.9.2
Fasteners in a metal that matches the cap

Call (904) 920-5495 Free Inspection

Measure, match, clear, fasten

Tiles measured on the roof
Each flue tile is measured inside and out, along with its height above the crown.
Cap style and metal chosen
Slip-in, band-mount or full-crown, in a metal suited to the roof, with a screen that meets the Florida code.
Flue cleared, cap fastened
Any nest or debris comes out of the flue, then the cap is set and fastened for wind.
Fit and screen checked
We check that the cap sits square, the hood height matches the chart and the screen comes off for the sweep.

Screens that clog near the coast

Soot sticks to a cap screen, and damp air helps it build up. A screen that met the open-area rule when new can narrow until the fire smokes into the room.

When we service chimneys in Nocatee, the screen is brushed clean, and a screen that cannot be cleaned is replaced.

10% off any service booked within 72 hours of inspection

Measured to the flue and fastened down, a new cap for your Nocatee chimney is 10% off.

Call (904) 920-5495 Free Inspection

Reading the grade on a stainless cap

Stainless steel is a family of alloys. Cap makers state the grade in their literature, and the grade sets how the cap resists corrosion. Two caps that look alike in a catalog photo can differ in grade and in the gauge of the sheet, and the thinner one dents and flexes more in wind. Both get named before a cap is ordered: the grade the maker specifies and the gauge of the hood and frame. Knowing the grade also tells a future contractor which fasteners and sealants are compatible, which matters when the cap is serviced years from now by someone who was not there when it went on.

Rain that slips past a cap

A cap sheds rain that falls straight down, but wind-driven rain can travel sideways under a shallow hood and into the tile. Some cap makers offer deeper hoods or models with side baffles for chimneys that stand exposed, and their literature says which.

Before we recommend a deeper hood, we confirm the water really arrives through the flue opening. Rain soaking through the crown or the brick shows up in the same firebox, and a larger hood does nothing about it. So the answer names the path we found, what closes it, and whether a bigger cap belongs in it at all.

Cap metal where salt reaches the roof

Salt carried on the wind settles on a cap and draws moisture to it, and chloride salt attacks metal that would last for years further inland. Some cap makers offer a Type 316 stainless line, sold as marine grade, for sites near salt water, since the molybdenum alloyed into 316 resists chloride pitting better than the common grade. A stainless-steel guide from the International Molybdenum Association adds that sheltered, rain-shadowed crevices hold salt longer than surfaces rain rinses, and a cap screen is full of such crevices. We follow the maker's grade guidance for the exposure, name the grade, and suggest rinsing the cap when the chimney is serviced.

What sets the cap on your estimate

Inside and outside size of each flue tile, measured on the roof
Crown condition under a full-crown cap, written as its own line
Nest, debris or animal removal needed before the cap goes on
Fastener metal matched to the cap to avoid galvanic corrosion

Cap questions we hear in Nocatee

Will you need to get inside the house?

Not for the roof work itself, as long as we can reach the roof safely. If the flue needs clearing from below, or an animal is involved, someone needs to let us in to the fireplace.

What does the screen on a cap have to meet?

Section R1003.9.2 of the Florida residential code sets the open area, the screen's heat and corrosion resistance, the opening size and removability for a spark arrestor on a masonry chimney. We check the cap we propose against each point.