Cracked flue tile repair in Neptune Beach

Top tiles replaced from the roof or joints resurfaced with a listed system, sized so your Neptune Beach fireplace still draws.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Family-owned flue experts serving Neptune Beach

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Appliance flues are repaired to suit the appliance, with the gas work left to a gas contractor.

Free inspection and estimateThe flue at your Neptune Beach home is swept, examined from both ends and mapped at no charge.
100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.

Call (904) 920-5495 Free Inspection

Joints that were never filled

Some flue gaps are as old as the chimney. Clay liners are supposed to sit on tight, smooth beds of refractory mortar, yet some flues were stacked with little or no mortar between the tiles.

An open joint lets heat and flue gas reach the masonry around the tile. It cannot be fixed by pouring something down from the top. It needs a listed resurfacing system or a new liner, depending on how many joints are open and where. Gaps between the tiles in your Neptune Beach flue? Call (904) 920-5495 and our flue specialists will look at no charge.

Neptune Beach is in Duval County. The 2020 Census count for Neptune Beach was 7,217 people.

What a flue repair covers in Neptune Beach

Flue swept, then examined from both ends
Seal around the top tile remade
Gaps at the smoke chamber closed
Flue mapped at your Neptune Beach home before any price is given

Call (904) 920-5495 Free Inspection

How chimney flue repair runs

Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.

Caps over repaired flues by the ocean

Salt-laden air rusts the metal of a cap that guards the flue, and a cap that fails leaves the tiles open to rain. Near the ocean, cap metal is part of the flue plan.

For Neptune Beach chimneys, a stainless cap in a grade suited to salt exposure is priced alongside any flue repair where the old cap has rusted.

10% off any service booked within 72 hours of inspection

The 72 hours for flue work in Neptune Beach start at your own inspection.

Call (904) 920-5495 Free Inspection

Why the code asks for a lined chimney

Section R1003.11 of the Florida residential code requires a lining in every masonry chimney, of a type that suits whatever appliance is connected, as its listing and maker direct. The liner is a separate duct inside the chimney walls, and its job is to carry smoke, gases and condensate up and out without letting them into the brick.

Repair work restores that duct. Whatever method is used, the result has to be a continuous, sealed passage from the bottom of the lining to the top. A repair that closes one crack but leaves an open joint below it has not done the job, which is why the whole flue is examined before any single fix is priced.

Flue size against the fireplace opening

For fireplace flues, the code offers a quick rule. A round flue needs a net area of at least 1/12 of the fireplace opening, a square one at least 1/10 (R1003.15.1). A second method uses a chart that also takes chimney height into account.

We measure both the flue and the opening before any repair that adds material inside the flue. Resurfacing adds thickness to every wall, and on a flue already near the limit that can tip it below the minimum. When the numbers are close, tile replacement or relining with a correctly sized liner is priced instead, with the measurements shown.

Why a generic patch is not a flue repair

R1003.11.1 limits flue linings to four kinds: clay tile made to ASTM C315, lining systems carrying a UL 1777 listing, factory-built chimney sections whose listing allows installation within masonry, and other approved materials able to take flue gases and condensate up to 1,800 degrees Fahrenheit without corroding, eroding, softening or cracking.

A tube of fireplace patch or a bag of masonry mortar pushed into a crack from above meets none of those. It may hide the crack, but it does not restore a lining. So a flue repair from us means new tile bedded in refractory mortar, or a resurfacing system with its listing, and the estimate says which one.

What goes on the flue map in Neptune Beach

Top tiles to replace from the roof, with the seal around them remade
Inlet thimble and cleanout door condition on appliance flues
Sections that could not be seen, and the access they need
Waiting time before a fire, per the mortar or coat maker

Before a flue repair is chosen

Does resurfacing make the flue smaller?

A little, because the coat adds thickness to every wall. We measure the flue and the fireplace opening first, and resurfacing is only offered when the flue will still meet the size the code asks for.

Is flue repair cheaper than relining?

When the damage suits a repair, it is usually the smaller job. When it does not, stacking repairs on a failing flue costs more in the end, and we price relining instead so you can compare.