Local chimney liner installation in Nassau Village-Ratliff

Insulated where the listing asks, connected where the appliance needs it and capped against the rain, in Nassau Village-Ratliff, once the free inspection is done.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Chimney liner specialists who prove the flue first

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

The flue is proved with a test piece first, so the liner and its insulation are sure to pass.

Free inspection and estimateWe sweep and measure the flue in Nassau Village-Ratliff at no charge before any liner is ordered.
Upfront pricing, no hidden feesLiner size, alloy, insulation and cap are one written price, set before the order goes in.
Workmanship warrantyHow we install the liner is covered by our workmanship warranty, and the maker's terms come in writing.

Call (904) 920-5495 Free Inspection

A new wood stove in an old fireplace

A fireplace flue is sized for an open fire, which is a far larger opening than a stove's collar. Set a stove into that fireplace and its exhaust crawls up a passage much too big for it, cools on the way, and leaves creosote and condensation on the walls.

Fitting a liner matched to the stove's outlet fixes the mismatch and gives the stove a sealed, cleanable flue from its collar to the cap. Have the stove's manual ready when we visit in Nassau Village-Ratliff, since it can set its own minimum flue height and connector rules on top of the liner's listing. What burns below the flue decides the liner, so have that ready when you ring (904) 920-5495.

Census takers counted 5,561 people in Nassau Village-Ratliff in 2020. Nassau Village-Ratliff does not reach the coast.

Chimney liner work we take on in Nassau Village-Ratliff

Flue proved with a test piece or guide cone
Liner diameter taken from the collar or the opening
Insulating blanket or poured mix where the listing asks
Tee and clean-out fitted below a stove connection

Call (904) 920-5495 Free Inspection

From proof run to capped liner in Nassau Village-Ratliff

Sweep and prove the flue
The flue is swept clean, then a test piece or cone is lowered to make sure the liner will pass every bend.
Size and alloy chosen
The diameter comes from the appliance collar or the fireplace opening, and the alloy from the fuel.
Liner run down and joined
The liner goes down with its insulation where the listing asks, and joins the stove, insert or smoke chamber below.
Top plate, cap and record
The top plate is clamped and sealed, the cap fastened, and you get the installation record.

One liner, one fuel in Nassau Village-Ratliff

Liner makers do not allow an oil appliance and a wood appliance to share one liner. Each needs its own flue.

When a chimney in Nassau Village-Ratliff serves two appliances, the estimate shows a liner for each.

10% off any service booked within 72 hours of inspection

The liner and its fittings for your Nassau Village-Ratliff chimney come 10% off together.

Call (904) 920-5495 Free Inspection

Proving the flue before a liner is ordered

A liner cut to length is not easily returned, so nothing is ordered on a guess. The proof run answers one question: will a liner of the planned size, with any insulation, pass from the top of this flue to the bottom?

It fails at bulging mortar joints, at tiles knocked out of line, and at offsets tighter than they look from either end. When the proof fails, the options are to break out the obstruction, change to flexible liner, or step down to a smaller rigid section if the appliance sizing still allows it. We say which option applies and why.

Where an aluminum liner fits, and where it does not

Aluminum liners have a narrow listing. The makers write them for Category I gas appliances, those fitted with a draft hood or listed for Type B gas vent, and the instructions rule out solid fuel, liquid fuel and gas appliances in Categories II through IV.

So aluminum is out for any flue that serves, or might later serve, a fireplace or stove burning wood. It can be the right choice for a gas appliance that matches its listing. Where the chimney's future use is uncertain, stainless keeps more options open, and we explain the trade.

Where the wall opening for a stove goes

When a stove connects through the side of the chimney, the opening in the masonry has to hold the connector firmly and keep the required clearance to any wood around it. Liner makers also ask that the opening not be placed directly behind the appliance, so the connection can be reached for inspection and cleaning.

If an old opening sits at the wrong height for the new stove, too close to framing, or behind where the stove will stand, a new opening is made and the old one closed with masonry. That work is priced separately from the liner.

Size, alloy and listing on paper

Stainless alloy picked from the listing for the fuel being burned
Broken tile and mortar bulges cleared out of the passage
Wall thimble checked for fit and clearance where the connector enters
Top plate sealed or screwed to the crown to carry the liner's weight

Relining questions from Nassau Village-Ratliff

Does a wood stove need a stainless liner?

The code requires the flue lining to suit the appliance, and a stove set into an existing masonry chimney needs a flue sized to its collar. Our answer is a listed stainless liner from the stove collar to the top, sized from the stove's manual.

Does a relined flue still need its own cap?

The relined flue does not need one. The liner kit we fit includes its own cap, which fastens at the top plate. If the chimney has other flues, their caps are checked, and any change is noted.