Gas log installation for Lakeside homes
A gas log set for your Lakeside fireplace, sized to the firebox and set to the manual after a free inspection of the flue and damper.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Gas log pros who measure first in Lakeside
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Gas logs in Lakeside go in only after the firebox has been measured against the set's table.
- Free inspection and estimateYour Lakeside firebox, flue, damper and room are measured against the set's manual at no charge before anything is bought.
- Upfront pricing, no hidden feesSet, burner, clamp, cleaning and any repairs are priced in writing, with the gas trade's part named.
- 100% satisfaction guaranteedIf the flame is sooty or the set will not stay lit after our installation to the manual, we come back.
Glass doors on the fireplace
Many wood fireplaces have glass doors, and gas logs change how they are used. The doors stay open while the logs burn, and a frame that blocks air along the floor of the fireplace can need changes before a set goes in. A frame without slots can starve the set of air along the floor.
The doors and frame are looked at during the measuring visit, since the opening with the doors swung back still has to meet the set's figures. Glass doors on a fireplace in Lakeside that is getting gas logs? Talk it through with us at (904) 920-5495.
Lakeside is part of Clay County. In the 2020 Census, Lakeside counted 31,275 residents.
Gas log work for Lakeside fireplaces
- Vented log sets with permanent damper clamps
- Fireboxes measured against the set's size table
- Lighting the new set together in your Lakeside living room
- Room size worked out before vent-free logs go into homes in Lakeside
How our gas log pros install a set in Lakeside
-
Measure firebox and room
Firebox, chimney height and, for vent-free sets, the room are checked against the manual.
-
Clean and clamp
Soot and debris come out of the fireplace, and vented sets get their permanent damper clamp.
-
Connect and test
Once gas reaches the valve, the set is connected, leak tested and its pressure read.
-
Place logs and light
Logs and embers go where the manual shows, and we light the set with you.
Gas pressure inland in Lakeside
A log set in Lakeside that fades when the furnace or water heater runs may be short of gas pressure.
We read the pressure with everything running.
10% off any service booked within 72 hours of inspection
Ready for gas logs? Book within 72 hours of the measuring visit and 10% comes off.
The oxygen sensing pilot on vent-free logs
Vent-free sets carry an oxygen depletion sensing pilot, which shuts the set off if the room's fresh air runs low. One maker's manual says the heater needs fresh air ventilation to run properly and points to its ventilation section if the set keeps shutting off.
Repeated shutoffs are a message about the room, not a nuisance to work around. We check the room volume, open connections and the house's tightness, and the sensing pilot is left exactly as the maker built it. The same maker notes that running above 4,500 feet of elevation can cause pilot outage. A shutoff after a long burn in a small room is the system doing its job.
The damper clamp on a vented set
A vented log set cannot run against a closed damper. One maker supplies a damper clamp that must be permanently installed, to keep a minimum opening and prevent the damper from closing fully, and says the damper must be fully open whenever the set is burning.
Where the clamp does not fit or fails to hold, the same maker calls for a permanent stop, removing the damper blade, or cutting the damper to leave the minimum opening. We fit the clamp as part of the install and show you why it is there. A handle painted open is not a substitute for the clamp.
How big the permanent damper opening must be
The permanent opening a clamp leaves is not guesswork. One maker's table sets it by chimney height and burner size: for a masonry fireplace with a 15-foot chimney, 27 square inches for its smallest burner, 35 for the middle size and 41 for the largest, with smaller figures for taller chimneys.
Factory-built fireplaces have their own column in the same table. We measure the opening the clamp leaves, compare it with the table for your chimney and set, and note the measurement on the ticket. An opening left too small is corrected before the first light, not after.
Measured in Lakeside before a log set is ordered
- Firebox front width, rear width, depth and height against the set's table
- Room volume set against the code's vent-free limit
- Supply pipe sized by the gas trade, with inlet pressure read at the valve
- Outside air ducts and ash doors closed off under vent-free sets
Before a log set goes in
Can gas logs go into any fireplace in Lakeside?
No. Vented logs need a sound fireplace and a chimney that draws, while vent-free logs need a big enough room where the rules allow them. Both are checked on a free visit.
What is the damper clamp for?
It fixes the damper partly open so exhaust from vented logs keeps a way out, even if someone reaches for the handle. Fitting it is part of our installation.
More services in Lakeside
-
-
-
-
-
-
Learn more about gas log installationAll services in Lakeside
A gas log set that fits your Lakeside fireplace
Know the log set you like? Tell us on (904) 920-5495 and our experts measure your Lakeside firebox against it.
Free Inspection