Gas fireplace installation in Lakeside by local specialists

Natural gas or propane, a free visit plans the Lakeside install, which ends with pressures read, connections leak-checked and the barrier fitted.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local gas fireplace experts for new installs in Lakeside

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Wiring for the blower and remote goes in before the wall is closed, so nothing gets cut open later.

Family owned and operatedOne family business frames, vents and starts up the unit in Lakeside, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

Planning the mantel and the finish

The wall around a gas fireplace is where the finish goes, and the manual sets the rules for it. Only noncombustible materials such as tile or stone may cover the metal face of the unit, fixed with an adhesive of the temperature rating the manual specifies.

A mantel has to sit at or above the height the mantel chart gives for its depth. If you have a finish in mind for your Lakeside room, we check it against the charts before anything is bought, and the framing includes blocking for the mantel at the right height. Checking a finish early is cheaper than removing it after the inspection. Natural gas or propane at your Lakeside home? Say which on the call to (904) 920-5495.

Lakeside lies within Clay County. Census takers counted 31,275 people in Lakeside in 2020.

Gas fireplace installs around Lakeside

Vent route drawn and checked against the vent table
Horizontal runs pitched the way the manual asks
Siding standoff fitted behind a wall termination
Facing and mantel planned from the manual's chart

Call (904) 920-5495 Free Inspection

From vent exit to first burn in Lakeside

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

Rear vent or top vent in Lakeside

Some direct-vent units ship as rear-vent models and can be converted to top vent. The choice sets the framing, so it is made before anything is built.

We pick the vent direction for your Lakeside install from the route to the outside wall or roof.

10% off any service booked within 72 hours of inspection

Direct-vent or natural-vent, the installation is discounted either way.

Call (904) 920-5495 Free Inspection

Pipe inside a pipe

Direct-vent pipe is coaxial: an inner pipe carries exhaust out, and the space between it and the outer pipe carries fresh air in. The two streams run side by side all the way to the termination, which has openings for both. Because the incoming air surrounds the hot inner pipe, the outer wall stays cooler than a single-wall vent would, and that is part of why the listed clearances to framing are small. The pipe, its joints and its termination are one listed system from the vent maker the manual names, and parts from another system are not mixed in.

What the unit sits on

The manuals we install from let a unit sit directly on wood flooring or a subfloor. When it would sit on carpet, tile or another combustible surface other than wood flooring, the manuals call for a metal or wood panel under the full width and depth of the unit. The unit is then secured to the floor or to the framing with the fasteners and points the manual shows, so it cannot shift when the facing is installed or the glass is removed for service. Raised platforms are built to the same rule, with the panel on top. The panel goes on before the unit is slid into place.

Facing materials and the heat they see

The metal face around the opening of a gas fireplace runs hot enough that the manual controls what goes over it. Only noncombustible finishes the manual accepts qualify, which rules out wood, paneling and ordinary drywall on that surface. Facing goes on with a high-temperature adhesive of the rating the manual names, and any joint sealed between the facing and the wall uses a high-temperature sealant. Wood trim and combustible board stay outside the zone the drawing marks.

Choosing a facing that meets those rules before it is bought avoids tearing it out after the inspection. Metal trim kits from the maker can frame it.

Unit, vent route and trades on paper

Wall thimble or roof parts from the vent maker's list
Noncombustible facing and mantel height checked against the charts
Service access panels left removable after the finish
Barrier screen fitted and logs set to the placement diagram

Gas fireplace install questions from Lakeside

Can a gas fireplace be installed in a house in Lakeside without a chimney?

Yes. A direct-vent unit uses its own listed vent pipe through a wall or the roof, so no chimney is needed. The site visit checks where the termination can go.

Do you run the gas line to the new fireplace?

No. The line to the unit's shutoff valve is a gas contractor's job, or the propane supplier's on a propane system. The estimate says who and when, and start-up follows once gas reaches the valve.