Direct vent gas insert installation in Lake Shore
Mantel, opening and flue in Lake Shore measured against the insert's rating plate before anything is ordered.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Gas insert pros who measure first in Lake Shore
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Liners follow the maker's height, offset and bend limits, not guesswork.
- Free inspection and estimateThe opening, flue and mantel of your Lake Shore fireplace are measured against the insert's plate at no charge.
- Upfront pricing, no hidden feesInsert, vent kit, surround, cleaning and repairs are priced line by line, and the gas and power trades are named.
- 100% satisfaction guaranteedIf the insert does not light, burn or seal the way its manual describes after our installation, we come back.
Does the insert fit the opening
Gas inserts are boxes of fixed size, and fireplaces are not. Openings narrow toward the back, lintels sit lower than they look and hearths rise at the front, so an insert that seems right in the showroom can fall short by half an inch on site. Splayed side walls are the usual surprise.
Tape measurements at the tightest points go on the estimate beside the maker's minimums, and the order waits until those numbers agree. Want to know whether a particular insert fits your Lake Shore fireplace? Book a measuring visit at (904) 920-5495.
Lake Shore is an inland community. Lake Shore is one of the named neighborhoods of Jacksonville.
What gas insert installation covers in Lake Shore
- Chimneys cleaned before any gas appliance connects
- Surrounds sized to uneven fireplace faces
- Pressure readings taken at the valve
- Yearly service set up from the first day
How gas insert installation runs
-
Measure against the plate
Opening, flue and mantel are checked against the insert's rating plate and manual.
-
Clean and check the chimney
The old flue is cleaned, examined and repaired if needed before the liners go up.
-
Liners, insert, surround
The vent kit runs to its termination, the insert is set and the surround fitted.
-
Hookups and first light
The gas and electrical hookups are made, then we light and test the insert with you.
An inland chimney that burned wood
Old wood chimneys in Lake Shore carry soot and debris from years of fires. The fuel gas code has them cleaned before a gas insert connects.
Cleaning is the first step of every install.
10% off any service booked within 72 hours of inspection
Gas inserts are larger jobs, and the 10% discount covers the whole install.
How tightly a liner may bend
Flexible liners can kink if they are forced around a tight corner, and a kink narrows the passage. One maker sets a minimum bend radius of 3 inches for its intake liner and 4 inches for its exhaust liner.
The tightest spots are usually at the throat and the smoke shelf, where the liners turn from the insert's adapter into the flue. We plan the route through those spots before pulling the liners, and where the damper frame or smoke shelf crowds the bend, the estimate says what is trimmed or removed to keep the radius.
Only the fronts made for the insert
Decorative fronts and doors for gas inserts are sold separately, and not all of them fit every model. One maker's manual allows only the doors and optional fronts approved with the unit to be installed on it.
A front from another model can block air openings, change how the glass seals or overheat, even if it looks like it fits. We order fronts from the parts list for the insert's model, and when a customer already has a front, we check its part number against that list before it goes on. The part numbers on the front and the plate should agree.
Resealing after service
The intake and exhaust of a direct-vent insert form a sealed path from outdoors to the firebox and back. One maker warns that the vent-air intake system has to be properly reinstalled and resealed after any servicing.
When an insert is pulled forward for service, the liner connections at its adapter are the joints most at risk. We reconnect them as the instructions show, check each joint and run the insert with the glass latched before leaving. A service call that leaves a liner loose behind the surround is worse than no call at all.
Measured in Lake Shore before a gas insert is ordered
- Inside flue size and route checked for the liners
- Vertical height and offsets measured against the vent limits
- Gas supply by the gas trade, with pressures read at the valve
- Model, vent kit and liner sizes recorded on the ticket
Before you switch to gas
Do you clean the chimney before the insert goes in?
Yes. A flue that carried wood smoke gets checked and cleaned under the state fuel gas code before any gas appliance is hooked to it, so that is step one.
Does a gas insert need yearly service?
Yes. Makers want a yearly check of the insert and its venting by someone qualified, and we can put that on the calendar from the day it goes in.
More services in Lake Shore
-
-
-
-
-
-
Learn more about gas fireplace insert installationAll services in Lake Shore
Easy heat from the fireplace in Lake Shore
Family-owned gas insert professionals look at your Lake Shore fireplace at no charge.
Free Inspection