Family-run gas fireplace insert installation in Lake Geneva

Local gas insert pros clean the old chimney, run the liners to the top and set the insert in Lake Geneva. The inspection is free.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local gas insert specialists who install to the listing

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

You deal with a local family business that explains what fits your Lake Geneva fireplace first.

Free inspection and estimateThe opening, flue and mantel of your Lake Geneva fireplace are measured against the insert's plate at no charge.
Upfront pricing, no hidden feesInsert, vent kit, surround, cleaning and repairs are priced line by line, and the gas and power trades are named.
100% satisfaction guaranteedIf the insert does not light, burn or seal the way its manual describes after our installation, we come back.

Call (904) 920-5495 Free Inspection

First light with the installer

The first time a new gas insert lights, we are there. The burner should catch across all its ports, the flame should settle into the pattern the manual shows, and the glass should stay clear. A light-up that takes too long or leaves some ports dark is corrected on the spot.

We run it through its controls with you, remote, wall switch or valve, and show you how the barrier comes off for cleaning. The manual stays with the house. Getting a gas insert in Lake Geneva? Book the install at (904) 920-5495 and we will light it with you.

The county for Lake Geneva is Clay County. Lake Geneva does not reach the coast.

What gas insert installation covers in Lake Geneva

Sealed direct-vent gas inserts installed to their manuals
Fireplace openings measured against the insert's plate
Co-axial and adapter kits where the manual calls for them
A first light with you at your Lake Geneva home

Call (904) 920-5495 Free Inspection

Measure, clean, reline, light

Measure against the plate
Opening, flue and mantel are checked against the insert's rating plate and manual.
Clean and check the chimney
The old flue is cleaned, examined and repaired if needed before the liners go up.
Liners, insert, surround
The vent kit runs to its termination, the insert is set and the surround fitted.
Hookups and first light
The gas and electrical hookups are made, then we light and test the insert with you.

Finishes around an inland insert

Updating the fireplace face in Lake Geneva along with an insert means checking the new materials against the manual.

Noncombustible finishes are the rule around a co-linear install.

10% off any service booked within 72 hours of inspection

Measured in Lake Geneva? Book the gas insert inside three days and 10% comes off.

Call (904) 920-5495 Free Inspection

Where co-linear liners may run

Placement rules for co-linear liners are narrow. One maker allows the co-linear portion only inside a solid-fuel-burning fireplace and its chimney, and rules out sharing a flue with a separate wood-burning appliance.

In other words, the liners use an existing wood fireplace and chimney as a chase, and the flue they occupy belongs to the insert alone. We check both conditions before planning a co-linear install, and a chimney with a wood stove on another flue gets a careful look at which flue the insert uses. The route is drawn on the estimate.

The termination at the top

At the chimney top, a co-linear system ends in a termination listed for that vent kit, set in its own flashing over the old flue. The termination keeps intake and exhaust apart so the insert does not draw in its own exhaust.

We check the chimney top before ordering, since the termination and its flashing sit on it. A cracked or loose top is repaired first. Once installed, the termination is fixed as its instructions show, and the ticket records the kit used. A termination blocked by debris gets checked early on any later service call.

Nothing added to the flame area

Decorative glass, stones and extra embers are tempting additions to a gas insert, but one maker warns against adding any material that will come in contact with the flames other than what it supplied with the appliance.

Material that does not belong on the burner can disturb the flame, cause soot and crack the glass. We set the logs, embers and media exactly as the manual shows on install day, and if you want a different look, we check the maker's list of approved media for that model before anything is changed. Approved media swaps are a simple job when the list allows them.

Opening, flue and mantel on paper

Chimney examined and cleaned before any gas appliance connects
Liner bend radius kept through the throat and smoke shelf
Termination and flashing at the chimney top, with the top checked first
Surround sized to the face, with noncombustible finishes around it

Gas insert questions from Lake Geneva

What is co-linear venting?

Two flexible liners run up the old flue, one bringing outdoor air in and one taking exhaust out. They join the insert at the bottom and a termination at the top.

How soon can the insert be installed?

Once the chimney is cleaned, the insert and kit have arrived and gas is at the valve. Call (904) 920-5495 and we will lay out the dates for your Lake Geneva installation.