Family-owned stone chimney repair in Kings Ferry
Our Kings Ferry masons match the joint style as carefully as the mortar color.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local stone masons who match mortar and joints in Kings Ferry
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Joints are raked to sound mortar and filled in layers, never skimmed over.
- Free inspection and estimateWhether your Kings Ferry chimney is full stone or veneer is settled on a free visit, before any price.
- Upfront pricing, no hidden feesStones, joints and veneer area are priced in writing one line at a time.
- Family owned and operatedOur family-owned masons approve the mortar sample with you before the first joint is filled.
Stone damaged after a storm
A storm can loosen stones at the top of a chimney, chip corners with flying debris, or open a crack in the crown that lets water behind the veneer. From the ground, the damage may be a single stone out of line. Loose stones at the top of the chimney are a falling hazard, not a cosmetic problem.
After a storm in Kings Ferry, keep clear of the chimney base if anything has fallen, and call (904) 920-5495. Our masons check the top courses, the crown and the veneer bond, and list what has to happen first and what can follow later.
Kings Ferry lies within Nassau County. Kings Ferry does not reach the coast.
Stone chimney repairs we handle in Kings Ferry
- Mortar matched to the stone's color and hardness
- Loose adhered veneer taken off and reinstalled
- Base drainage exits opened and restored
- Stone cleaned by tested, gentle methods
From the first loose stone to the last tooled joint in Kings Ferry
-
Describe what moved
Tell us what has shifted or fallen, and the free visit comes equipped for it.
-
Build and backing confirmed
Corners, joints and the base show the build, and a loose piece shows what is behind the veneer.
-
Reset, repoint or reinstall
Stones go back on fresh beds, joints fill in layers, and veneer returns to a repaired backing.
-
Matched and cured
An approved mortar sample and the old joint profile guide the finish, and the cure time is written down.
Storm season and stone chimneys in Kings Ferry
From June 1 to November 30, the Atlantic hurricane season as the National Hurricane Center defines it, strong wind can loosen top stones or crack a crown far from the shore. In Kings Ferry, a stone out of line at the top is worth a look before the next storm.
The top courses and the crown get a look after each storm.
10% off any service booked within 72 hours of inspection
On a stone chimney in Kings Ferry, the mortar match and the discount both go in writing.
Where veneer meets the roof
Veneer installation guides call for a gap between the bottom of the stone and the roof surface, with flashing and the water barrier lapped so water drains out over the roofing. Stone set tight to the shingles pulls water up into the veneer, and the base of the stone stays wet.
The gap and the flashing detail come from the veneer maker's guide for the product on your chimney. Where the stone sits on the roof, we cut it back and correct the detail, and flashing work is priced on its own line. Cutting stone back at the roof is done with care for the roofing below, which is protected before any saw is used.
Getting sealant out of stone joints
Caulk or foam packed into stone joints blocks them from drying and leaves the old mortar behind it wet and soft. It also bonds to the stone edges, so pulling it out can take the edge of a soft stone with it.
We cut sealant out with blades rather than tearing it, then rake the joint to sound mortar and repoint. Sealant stays only where a moving joint needs it, such as between the crown and the flue liner, and the ticket says where. Silicone residue left on stone faces can stop new mortar from bonding, so the edges are cleaned before repointing.
Working on stone from the roof
Stone work on a chimney happens on the roof and on ladders, with stones and mortar carried up. We protect the roofing around the chimney, keep loose material from sliding off the roof, and stage the work so nothing heavy sits on the shingles.
Where the chimney is tall or the roof is steep, the estimate includes the access equipment needed to work safely. It is part of doing stone work properly, and it is listed so you can see it. Loose stone and debris are lowered, not thrown, so nothing damages the roof, the gutters or the ground below.
Stone, joints, backing and base, in writing
- Build identified as full stone, anchored veneer or adhered veneer
- Joint profile matched to the existing work
- Water barrier and lath repaired before veneer is reset
- Old cement patches and caulk cut out before repointing
Stone chimney questions from Kings Ferry
Do you charge to look at a stone chimney in Kings Ferry?
No. The stone, the joints, the top and the base are all checked, and the written estimate costs you nothing.
Do you repair manufactured stone veneer as well as natural stone?
Yes. Manufactured veneer follows its maker's installation guide for the backing and setting mortar, and we match the product line and color as closely as it allows.
More services in Kings Ferry
-
-
-
-
-
-
Learn more about stone chimney repairAll services in Kings Ferry
Loose stones or failing veneer in Kings Ferry?
Book the free stone chimney inspection in Kings Ferry; stone work agreed in the three days after it comes 10% off.
Free Inspection