Tuckpointing chimneys in Kings Ferry by local masons
Every face of your Kings Ferry chimney mapped for free, then a written price for each side.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Family-owned mortar specialists serving Kings Ferry
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
If a joint we repointed in Kings Ferry lets go, the same family crew returns to fix it.
- Free inspection and estimateEvery face of your Kings Ferry chimney is scratch-tested and sketched at no charge.
- 100% satisfaction guaranteedIf the new joints are not sound, full and matched as agreed, we come back and fix them.
- Family owned and operatedA family masonry crew does the survey and the work, so the person who priced a face is the one who repoints it.
Hard gray mortar next to soft brick
Old chimneys were often laid in softer mortar than today's strong mixes. When a later repair filled the joints with hard gray mortar, the stress of movement and drying can shift into the brick instead, and the brick edges beside the new joints start to crumble.
Repointing an older chimney means choosing a mortar softer than its brick, as preservation guidance advises. We check the brick and the old mortar before picking a type. Crumbling brick edges beside newer joints in Kings Ferry? Phone (904) 920-5495, and our family masons will look at it for free.
Kings Ferry sits in Nassau County. Kings Ferry sits away from the coastline.
What chimney tuckpointing covers in Kings Ferry
- Deep joints filled in layers, not one pass
- Color matched from a cured sample
- Roof and yard protected, debris cleaned up
- Brick faces brushed clean as we go
Survey, rake, fill, tool
-
Every face surveyed
Joints are scratch-tested at several heights and the failed courses marked on a sketch.
-
Joints raked and cleaned
Old mortar comes out to sound depth, head joints by hand, then joints are cleaned and dampened.
-
Filled in layers and tooled
Matched mortar goes in stage by stage, then is tooled to the original profile.
-
Cured and cleaned up
Fresh joints are protected while they cure, the faces brushed and the roof cleared.
Uneven wear around Kings Ferry chimneys
Shade, sun and rain direction make one face of a chimney age faster than another, wherever the house sits.
Each face of a chimney in Kings Ferry is priced separately, so the worst side can go first.
10% off any service booked within 72 hours of inspection
Sandy joints? Book the repointing within 72 hours of the survey and 10% comes off.
Why head joints are cut by hand
The short vertical joints between bricks in a course are the head joints. They are narrow and short, and a grinder blade that slips there cuts into the brick on either side, leaving a scar that shows long after the job.
Preservation Brief 2 advises against power tools on head joints for that reason. We cut them by hand with a plugging chisel, which is slower but leaves the brick edges intact. The time that takes is part of why a repointing quote is priced by the joint, not by the square foot of wall.
When the top needs relaying, not repointing
Repointing works where the bricks are still bedded firmly and only the joints have worn. When a row of bricks rocks under a hand, the mortar has failed through, and new mortar at the face will not hold the course together.
Those courses are taken down and relaid in fresh mortar, which is a rebuild of the top rather than tuckpointing. We identify how far down the looseness goes before pricing. Below that point, the joints can often still be repointed in place, and the two jobs are listed separately so you see where one ends.
Mortar inside the house and attic
The exterior of a chimney gets the attention, but the section inside the house and attic has mortar joints too. There, a failed joint is not only a cosmetic issue, since the chimney wall sits close to the framing.
Where the chimney is visible in the attic or a closet, we check those joints with a light. Sandy or open joints on the interior are repointed with the same care as outside, with the space protected from dust. They are listed separately on the estimate because the access and cleanup are different. Any joint there that looks scorched or blackened is noted for a flue check as well, since it may point to a leak from inside.
Joint findings written down before pricing
- Color matched from a cured test batch shown to you first
- Caulk or skim patches to remove before repointing
- Interior or attic joints, with their own access and cleanup
- Weather protection and curing for the new joints
Repointing questions from Kings Ferry
How close will the new mortar color be?
A sample batch is mixed, cured beside your brick and checked in daylight before any joint is filled. New joints can still look slightly fresher at first, and we show you the sample so you know what to expect.
Which mortar will you use?
A type from ASTM C270 picked for your brick and its exposure, normally weaker than the brick itself, in line with preservation guidance. The type is written on the estimate.
More services in Kings Ferry
-
-
-
-
-
-
Learn more about chimney tuckpointingAll services in Kings Ferry
Repoint a worn chimney in Kings Ferry
Mortar crumbling in Kings Ferry? Tell us which sides at (904) 920-5495, and we start the survey there.
Free Inspection