Gas fireplace installation in Jacksonville Beach by local specialists

Direct-vent or B-vent, an installation in Jacksonville Beach starts with a free visit to see where the vent can exit and what it has to clear.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Gas fireplace install specialists for Jacksonville Beach

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Start-up includes pressure readings and a leak check, written on your Jacksonville Beach record.

Family owned and operatedOne family business frames, vents and starts up the unit in Jacksonville Beach, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

See-through and corner units

Not every gas fireplace has one face. See-through units open into two rooms, corner units show two sides of the flame, and some models show three. Each design has its own framing drawing, clearances on more than one side and its own vent options, and a see-through unit's framing has to work from both rooms.

We review the drawing with you in both Jacksonville Beach rooms, confirm the vent can leave from where the unit sits, and note any finish that has to be matched on both faces. Both faces also need the barrier screen and service access the manual calls for. Natural gas or propane at your Jacksonville Beach home? Say which on the call to (904) 920-5495.

Jacksonville Beach is part of Duval County. The 2020 Census count for Jacksonville Beach was 23,830 people.

From vent exit to first burn

Heater or decorative listing matched to your plan
Vent route drawn and checked against the vent table
Wiring for the receiver and blower run before the wall closes
Facing and mantel planned from the manual's chart

Call (904) 920-5495 Free Inspection

How our gas fireplace pros install a unit in Jacksonville Beach

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

New installs in Jacksonville Beach through hurricane season

Hurricane season covers June 1 through November 30. A new hole through the outside wall or roof has to be closed and sealed at the end of each work day.

We plan the exterior work in Jacksonville Beach around the forecast, and the opening is covered until the termination is sealed in.

10% off any service booked within 72 hours of inspection

Direct-vent or natural-vent, the installation is discounted either way.

Call (904) 920-5495 Free Inspection

The clear zone in front of the cap

The space in front of a wall termination has to stay open so exhaust can disperse and fresh air can reach the intake. Manuals set a clear distance in front of the cap free of shrubs, fences, sheds, decks and other obstructions. A spot that is clear today can be crowded later by a hedge or a new fence, so we point out the zone when the termination goes in and note it for anyone doing landscaping.

Where a guard is needed because the cap sits within reach of people, the vent maker's guard is used. The zone is noted on the plan too.

What the unit sits on

The manuals we install from let a unit sit directly on wood flooring or a subfloor. When it would sit on carpet, tile or another combustible surface other than wood flooring, the manuals call for a metal or wood panel under the full width and depth of the unit. The unit is then secured to the floor or to the framing with the fasteners and points the manual shows, so it cannot shift when the facing is installed or the glass is removed for service. Raised platforms are built to the same rule, with the panel on top. The panel goes on before the unit is slid into place.

Choosing termination parts near salt spray

Salt spray speeds up corrosion of exposed steel, and a new vent termination spends its life outdoors. Near the coast, we look at what the vent maker offers for the termination, its trim and its fasteners, including stainless or coated options where the maker lists them, and use those parts on the exterior. The termination is placed where it can be reached for rinsing and inspection, and the manual's clearances still govern its spot. The corrosion-resistant parts chosen are recorded, so they can be matched if anything is replaced later. Rinsing the cap with fresh water now and then slows the salt down.

Checked outside and in before an install in Jacksonville Beach

Unit named by maker and model, with its heater or decorative listing
Termination spot measured to windows, soffits, corners and walks
Wall thimble or roof parts from the vent maker's list
Service access panels left removable after the finish

Before the vent hole is cut

Does a gas fireplace need an electrical outlet?

Units with electronic ignition or a blower do, in the location the manual shows, and an electrician adds it if one is not there. A standing-pilot unit without a blower can run with no house power.

Is a permit needed for a gas fireplace?

Yes. The permit comes from the local building department, and its inspections cover the gas connection, the vent and the framing before the finish closes them in. Both appear on the estimate.