Local gas fireplace installation in Hilliard

Direct-vent or B-vent, an installation in Hilliard starts with a free visit to see where the vent can exit and what it has to clear.

Family owned and operated
Free inspection and estimate
Same-day service available
Upfront pricing, no hidden fees

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

or call (904) 920-5495

Why Choose Us

Gas fireplace installation specialists who vent to the manual

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off when you book today

Gas lines are run by a gas contractor or the propane supplier, and we set out who and when.

Family owned and operatedOne family business frames, vents and starts up the unit in Hilliard, and lines up the gas and electrical trades.
Free written estimatesThe unit, vent parts, framing, permit and every trade are on one free written estimate.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

Power for blowers and electronic ignition

Some gas fireplaces run on a standing pilot with no house power at all. Others use electronic ignition, a blower or both, and those need an outlet in the spot the manual gives, sometimes within the unit's control area.

Any new outlet or circuit is added by an electrician. The manuals also call for the appliance to be grounded to the electrical code, and they ask for the wall switch, remote receiver and fan wiring to be run before the wall is finished. The electrician's part, and when it happens, is set out for your Hilliard job. Picked a room for a gas fireplace in Hilliard? (904) 920-5495 is the number for a free planning visit.

Hilliard is in Nassau County. In the 2020 Census, Hilliard counted 2,967 residents.

What's Included

What a gas fireplace installation covers in Hilliard

Vent route drawn and checked against the vent table
Siding standoff fitted behind a wall termination
Wiring for the receiver and blower run before the wall closes
Walk-through of your new Hilliard unit and its manual

Call (904) 920-5495 Free Inspection

How It Works

How gas fireplace installation runs

Unit and vent route chosen
We pick a listed unit for the room and draw the vent route against the manual's vent table.
Framed and vented to the manual
Framing, header and clearances come from the manual, and the vent is run with its firestops and supports.
Gas and power by their trades
A gas contractor or the propane supplier brings gas to the shutoff valve, and an electrician adds any outlet.
Start-up readings and leak check
Pressures are read at the valve, every joint is leak-checked, the flame is checked and the barrier fitted.

Local Conditions

Bedrooms and B-vent units in Hilliard

A B-vent fireplace takes its air from the room, so the fuel gas code limits it in bedrooms to rooms of a set size. A sealed direct-vent unit avoids that limit.

We check the room size in your Hilliard home before recommending either type.

10% off your first service when you book today

A new gas fireplace booked today in Hilliard comes with 10% off a first service.

Call (904) 920-5495 Free Inspection

Pipe inside a pipe

Direct-vent pipe is coaxial: an inner pipe carries exhaust out, and the space between it and the outer pipe carries fresh air in. The two streams run side by side all the way to the termination, which has openings for both. Because the incoming air surrounds the hot inner pipe, the outer wall stays cooler than a single-wall vent would, and that is part of why the listed clearances to framing are small. The pipe, its joints and its termination are one listed system from the vent maker the manual names, and parts from another system are not mixed in.

The clear zone in front of the cap

The space in front of a wall termination has to stay open so exhaust can disperse and fresh air can reach the intake. Manuals set a clear distance in front of the cap free of shrubs, fences, sheds, decks and other obstructions. A spot that is clear today can be crowded later by a hedge or a new fence, so we point out the zone when the termination goes in and note it for anyone doing landscaping.

Where a guard is needed because the cap sits within reach of people, the vent maker's guard is used. The zone is noted on the plan too.

Propane tanks and the fireplace

A propane fireplace runs off a tank outside the house, and the manuals are explicit that propane tanks do not go inside any structure. Some manuals set a minimum tank size so the tank can vaporize enough gas to keep up with the unit, which matters on small tanks.

The regulator at the tank and the line to the house belong to the propane supplier. We confirm with the supplier that the tank, regulator and line suit the fireplace's input before the unit is ordered, so start-up is not the first time anyone checks. The supplier's answer is kept with the installation plan.

Free Inspection

Checked outside and in before an install in Hilliard

Noncombustible facing and mantel height checked against the charts
Inlet and manifold pressures read and recorded at start-up
Barrier screen fitted and logs set to the placement diagram
Permit and inspections placed in the schedule

FAQ

Before the vent hole is cut

Do you run the gas line to the new fireplace?

No. The line to the unit's shutoff valve is a gas contractor's job, or the propane supplier's on a propane system. The estimate says who and when, and start-up follows once gas reaches the valve.

Is a direct-vent unit or a B-vent unit better?

It depends on the room and the route. A direct-vent unit is sealed and can exit through a wall, and it is allowed in bedrooms when installed to its listing. A B-vent unit uses room air and needs a vertical vent through the roof.

Our Services