Gas fireplace insert installation in Hilliard
Mantel, opening and flue in Hilliard measured against the insert's rating plate before anything is ordered.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Gas insert experts for Hilliard homes
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Pressures are read at the valve and joints leak tested once gas arrives.
- Free inspection and estimateThe opening, flue and mantel of your Hilliard fireplace are measured against the insert's plate at no charge.
- Upfront pricing, no hidden feesInsert, vent kit, surround, cleaning and repairs are priced line by line, and the gas and power trades are named.
- 100% satisfaction guaranteedIf the insert does not light, burn or seal the way its manual describes after our installation, we come back.
Natural gas or propane
Every gas insert leaves the factory set for one fuel, and the rating plate names it along with the pressures the valve expects. Switching fuels is done only with the maker's own conversion kit, not by drilling or swapping parts on site. Pressures at the valve are read against that plate once gas arrives.
The fuel at the house is confirmed before a model is chosen, and the propane supplier or gas company is in the plan from day one. Propane at a house in Hilliard and wondering about an insert? Ask a gas insert specialist at (904) 920-5495.
Hilliard had 2,967 residents at the 2020 Census. Hilliard is an inland community.
What gas insert installation covers in Hilliard
- Sealed direct-vent gas inserts installed to their manuals
- Mantel clearances checked for height and depth
- Barrier screens and relief doors checked
- A first light with you at your Hilliard home
How gas insert installation runs
-
Measure against the plate
Opening, flue and mantel are checked against the insert's rating plate and manual.
-
Clean and check the chimney
The old flue is cleaned, examined and repaired if needed before the liners go up.
-
Liners, insert, surround
The vent kit runs to its termination, the insert is set and the surround fitted.
-
Hookups and first light
The gas and electrical hookups are made, then we light and test the insert with you.
Natural gas or propane in Hilliard
Some homes in Hilliard have natural gas and some run on propane. The insert is ordered for the gas the house has.
The supplier is booked alongside the install.
10% off any service booked within 72 hours of inspection
Switching to gas? Book the insert within 72 hours of the inspection and take 10% off.
How tightly a liner may bend
Flexible liners can kink if they are forced around a tight corner, and a kink narrows the passage. One maker sets a minimum bend radius of 3 inches for its intake liner and 4 inches for its exhaust liner.
The tightest spots are usually at the throat and the smoke shelf, where the liners turn from the insert's adapter into the flue. We plan the route through those spots before pulling the liners, and where the damper frame or smoke shelf crowds the bend, the estimate says what is trimmed or removed to keep the radius.
The barrier screen on a new insert
Inserts built to the 2015 revisions of the ANSI gas fireplace standards ship with a mesh guard for their glass. One insert plate makes fitting it mandatory and sends you back to the same maker when a guard is damaged.
We fit the barrier at installation and make sure it is seated before the first light. Any screen removed for service goes back on before the insert runs again. The glass behind it stays hot for some time after the flame is out, which is exactly when the barrier earns its place. The guard also comes off for glass cleaning, and it is put back before the next light.
Pressure relief doors stay closed
Some gas inserts have pressure relief doors, which let the firebox vent a sudden pressure rise. One maker warns that these doors must be kept closed while the appliance runs, because exhaust containing carbon monoxide could otherwise enter the home, and the hot gases could overheat nearby materials.
On install day we check that relief doors seat properly and show you what they look like, so no one props one open or removes it. A relief door that will not stay closed is a reason to shut the insert off and call for service. They are part of the design, not a loose panel.
Measured in Hilliard before a gas insert is ordered
- Fireplace opening width, height and depth against the insert's plate
- Vertical height and offsets measured against the vent limits
- Liner bend radius kept through the throat and smoke shelf
- Barrier screen fitted and relief doors checked
Before you switch to gas
Do you clean the chimney before the insert goes in?
Yes. A flue that carried wood smoke gets checked and cleaned under the state fuel gas code before any gas appliance is hooked to it, so that is step one.
Who runs the gas line?
The gas trade does: a gas contractor, the gas company or your propane supplier. Their part is on the estimate with a date, and our hookup follows once gas reaches the valve.
More services in Hilliard
-
-
-
-
-
-
Learn more about gas fireplace insert installationAll services in Hilliard
Switch your Hilliard fireplace to gas
Our gas insert pros measure your Hilliard opening, flue and mantel before you buy. Call (904) 920-5495.
Free Inspection