Wood stove insert installation in Hilliard
Each wood insert fitted in Hilliard carries an EPA Step 2 label and goes in to its listing, after a free inspection.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local insert pros who install to the listing
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
An insert in Hilliard goes in only after the fireplace has been measured against the insert's own table.
- Free inspection and estimateYour Hilliard firebox, chimney height and hearth are measured against the insert's manual at no charge, before anything is ordered.
- Upfront pricing, no hidden feesEvery part of the job is priced before ordering, from repairs to the rain cap, and nothing is added without your yes.
- 100% satisfaction guaranteedIf the insert smokes or draws poorly after installation to its manual, we come back and set it right.
What goes up the chimney with an insert
Running a liner up an old flue is most of the work of an insert installation. The liner goes in from the top, down through the damper area into the fireplace, and connects to the insert's collar, while a top plate and a rain cap close the old flue around it.
Each piece is listed on the estimate with its size and material, and the liner's length is measured before ordering so nothing arrives short. Curious what an insert install involves at your Hilliard house? Walk through it with us on a free visit booked at (904) 920-5495.
The 2020 Census count for Hilliard was 2,967 people. Hilliard is an inland community.
Liner, surround, clearances and hearth
- Listed wood inserts installed to their manuals
- Full-length stainless liners sized to the collar
- Outside air kits through the old ash chamber
- EPA Step 2 labels checked on every new insert
How insert installation runs
-
Measure against the manual
Firebox, chimney height, hearth and clearances are checked against the insert's table before ordering.
-
Repair and clean first
Fireplace repairs are made and cured, and the flue is cleaned before the liner goes up.
-
Liner, plate and cap
A listed stainless liner runs to the top, closed with a top plate and a rain cap.
-
Set, seal and fire
The insert and surround go in as the manual directs, and the first fire is run with you.
Draft on an inland chimney in Hilliard
Well back from the coast, an insert's performance comes down to the chimney: its height and the liner size. One maker sets a 15-foot minimum height for its model.
We measure the chimney in Hilliard before recommending a unit.
10% off any service booked within 72 hours of inspection
An insert for a home in Hilliard is a larger job, and the discount still applies to all of it.
Why a full-length liner is the usual choice
Manuals allow two ways of connecting an insert to the chimney. The fuller one is a stainless steel liner, rigid or flexible, from the flue collar of the insert all the way up to the chimney top. One maker calls this the safest installation and says it lets the insert draft correctly, avoiding difficult start-ups and smoke out the door.
A liner the size of the insert collar also keeps the smoke moving faster than it would in a large old flue, which helps the insert burn as designed. That is the installation we recommend and price by default, with any other option listed beside it and its trade-offs named.
Sizing the liner to the collar
The insert collar sets the liner size. One maker's insert uses a 6-inch stainless liner, and its manual shows the liner attached to a stove connector at the insert and running full length above it.
A liner smaller than the collar chokes the insert, and one larger than needed gives slow, cool smoke the same way the old flue did. We confirm the collar size on the unit itself, check that the flue has room for the liner and any insulation the listing calls for, and order to that size. Where the flue is too tight, the estimate says so before the order.
Outside air through the old ash chamber
Certain inserts can take combustion air from outdoors. One maker routes it through an existing ash clean-out: the cover comes off, a rodent screen goes in its place, and the insert's rear air intake draws from the chamber once the surround is sealed.
That only works where the ash chamber leads outside and stays clear, which we check before recommending it. The same maker advises checking local codes on combustion air. Where outside air is not available, the insert runs on room air with the surround left as its manual directs, and we explain what that means for the room.
Measured in Hilliard before an insert is ordered
- Fireplace cracks, loose mortar and throat condition repaired before install
- Top plate trimmed, seated and sealed, with a rain cap on the liner
- First fire run with you, covering the air control and loading
- Separate lines for repairs, liner, insert, surround and cap
Before you order an insert
Can I keep my mantel?
Often, if it clears the distance on the insert's label. When it does not, you pick a model with smaller clearances or rework the trim, and we measure before you order.
Is the inspection before an insert free?
Yes. Measuring the firebox, checking the chimney and writing the estimate cost nothing, and the price is set out upfront. Order the insert within 72 hours of that visit and the job is 10% off.
More services in Hilliard
-
-
-
-
-
-
Learn more about wood-burning fireplace insert installationAll services in Hilliard
Insert questions, free visit
A free insert inspection in Hilliard is one call to (904) 920-5495, and you save 10% on the install by booking within 72 hours of it.
Free Inspection