Gas fireplace insert installation in Garden City
A sealed gas insert for your Garden City fireplace, installed to its listing after a free inspection of the opening, the flue and the mantel.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local gas insert specialists who install to the listing
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Gas piping belongs to the gas trade and new circuits to an electrician, named in writing.
- Free inspection and estimateThe opening, flue and mantel of your Garden City fireplace are measured against the insert's plate at no charge.
- Upfront pricing, no hidden feesInsert, vent kit, surround, cleaning and repairs are priced line by line, and the gas and power trades are named.
- 100% satisfaction guaranteedIf the insert does not light, burn or seal the way its manual describes after our installation, we come back.
A chimney that serves two fireplaces
Some chimneys carry two flues, one for each fireplace, and sometimes a wood stove shares the stack. A gas insert's pipes need a flue that nothing else uses, and its maker rules out any hookup to a flue that also serves a solid-fuel appliance. Two fireplaces on one chimney can each have their own insert, one flue apiece.
Every flue on the chimney is traced before the pipes are planned, so the insert gets one of its own. Chimney with more than one flue at your Garden City house? Have it checked at (904) 920-5495 before choosing an insert.
Garden City lies inland. Within Jacksonville city limits, Garden City is its own named neighborhood.
Gas insert work for Garden City fireplaces
- Co-linear liners run to a listed termination
- Dampers removed or fixed open for the liners
- Surrounds sized to uneven fireplace faces
- Pressure readings taken at the valve
How our gas insert pros install an insert in Garden City
-
Measure against the plate
Opening, flue and mantel are checked against the insert's rating plate and manual.
-
Clean and check the chimney
The old flue is cleaned, examined and repaired if needed before the liners go up.
-
Liners, insert, surround
The vent kit runs to its termination, the insert is set and the surround fitted.
-
Hookups and first light
The gas and electrical hookups are made, then we light and test the insert with you.
An old damper inland in Garden City
Dampers in old fireplaces in Garden City may be rusted or stuck. For a gas insert, the plate is removed or fixed open for the liners.
We write down what was done.
10% off any service booked within 72 hours of inspection
Quote the 10% off when you order the gas insert, and it shows as its own line.
Co-axial venting, one pipe inside another
With co-axial pipe, exhaust rises through a pipe nested inside a larger intake pipe, and outdoor air comes down the ring of space around it. It is the arrangement many direct-vent fireplaces use through a wall or roof.
Inside a chimney, co-axial pipe needs a straighter, wider path than two flexible liners do. Some installations use co-axial pipe for part of the run and an adapter to co-linear liners for the rest. Which applies depends on the insert's manual and the shape of your flue, and the estimate names the kit chosen. Rigid co-axial sections also need more room at the throat than flexible liners.
Finishes around the fireplace
The surround panels of an insert sit against the fireplace face, and what surrounds them matters too. One maker's co-linear venting sheet states that any finishes applied around the fireplace must be noncombustible.
Tile, stone and brick meet that rule; wood trim close to the opening usually does not. When the fireplace face is being updated at the same time as the insert goes in, we check the planned materials against the manual before the finisher starts, so the new face does not have to come off again. Wood trim can often move a few inches outward instead of coming off entirely.
Resealing after service
The intake and exhaust of a direct-vent insert form a sealed path from outdoors to the firebox and back. One maker warns that the vent-air intake system has to be properly reinstalled and resealed after any servicing.
When an insert is pulled forward for service, the liner connections at its adapter are the joints most at risk. We reconnect them as the instructions show, check each joint and run the insert with the glass latched before leaving. A service call that leaves a liner loose behind the surround is worse than no call at all.
Measured in Garden City before a gas insert is ordered
- Chimney examined and cleaned before any gas appliance connects
- Surround sized to the face, with noncombustible finishes around it
- Outlet position behind the surround, wired by an electrician where needed
- First light run with you, burner catching across all ports
Before you switch to gas
Will the insert work in a power outage?
Some models light and adjust on batteries while the blower stays off; others need house power. We check the model you are considering before you buy.
Can I keep my mantel?
Yes, when its height suits its depth under the insert's figures. Otherwise the choice is another model, a higher mantel or a noncombustible one, settled before ordering.
More services in Garden City
-
-
-
-
-
-
Learn more about gas fireplace insert installationAll services in Garden City
Switch your Garden City fireplace to gas
Our gas insert pros measure your Garden City opening, flue and mantel before you buy. Call (904) 920-5495.
Free Inspection