Chimney cap replacement in Garden City by local cap pros
Every cap we fit in Garden City lifts off for cleaning and goes back on tight. Ask our cap pros for a free inspection.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local cap experts for Garden City chimneys
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
We fit caps in Garden City ourselves, from the tape measure on the tile to the last screw.
- Free inspection and estimateWe measure every flue on your Garden City chimney at no charge before any cap is ordered.
- Upfront pricing, no hidden feesThe cap model, its metal and the fastening are priced together, so the total is clear.
- Workmanship warrantyOur fitting and fastening carry the workmanship warranty, with the cap maker's terms in writing.
Caps and top-sealing dampers
A top-sealing damper sits where a cap would, on top of the flue tile, and closes with a cable run down to the firebox. Its lid sheds rain, and where the model includes a screen, animals stay out too, so it takes the place of a cap rather than sitting underneath one. In any Garden City house whose throat damper no longer closes tight, it can solve both problems in one fitting. We price a standard cap and the damper side by side when both would fit the tile, and we note any appliance in the firebox that has to keep the flue open, since that rules the damper out. The flue gets measured on the free visit in Garden City, before any cap is ordered; call (904) 920-5495.
Garden City is a neighborhood within the City of Jacksonville. Garden City sits in Duval County.
Every cap job, tile to screw
- Slip-in, band-mount or full-crown style picked to suit the tile
- Screen openings checked against Florida code R1003.9.2
- Two-flue chimneys fitted with two caps or one cover
- Crown condition noted under a full-crown cap
Measure, match, clear, fasten
-
Tiles measured on the roof
Each flue tile is measured inside and out, along with its height above the crown.
-
Cap style and metal chosen
Slip-in, band-mount or full-crown, in a metal suited to the roof, with a screen that meets the Florida code.
-
Flue cleared, cap fastened
Any nest or debris comes out of the flue, then the cap is set and fastened for wind.
-
Fit and screen checked
We check that the cap sits square, the hood height matches the chart and the screen comes off for the sweep.
Soot-clogged screens in Garden City
The screen on a cap catches soot from every fire. Over a season the openings narrow, and the fire becomes slow to start and smoky.
When a chimney in Garden City starts drawing poorly, the cap screen is one of the first things we check and clean.
10% off any service booked within 72 hours of inspection
Even a small job like a cap gets the full discount.
Soot-clogged mesh and a lazy fire
Screen mesh sits in the path of every bit of soot and creosote that leaves a wood fire. Over a season the deposit narrows the openings, and a mesh that met the open-area rule when new may fall short. The symptoms show inside the house: a fire that is slow to catch, smoke that curls out at the top of the opening, and a smell of smoke in the room the next day. Brushing the mesh during a sweep clears it. When the mesh size is within the code, a screen that clogs again quickly usually points to how the fires are burned, with wet wood or too little air, rather than to a fault in the cap.
Water the cap cannot stop
The cap guards only the flue opening. The crown around it takes the same rain, and when it cracks or pulls away from the flue tile, water enters the top of the masonry and runs down inside the chimney. The result looks just like an uncapped flue from below: water in the firebox and rust on the damper. That is why a cap visit includes a close look at the crown surface and the joint where the crown meets the tile. When crown repair is needed, it appears as its own line, priced apart from the cap, making it clear that the new cap was not sold as a cure for a crown leak.
Why the old cap is not the pattern
Ordering a replacement to match the cap that came off is tempting. The trouble is that the old cap may not have fit in the first place. Caps sized a step too small get forced over a tile and crack it; caps a step too large sit loose and walk off in wind. Some were fitted before the crown was redone and no longer match the tile height at all.
So we measure the tile and the crown as they are today and size from the maker's chart, and the old cap leaves the roof with its fasteners. The measurements stay on file for whoever services the chimney next.
What sets the cap on your estimate
- Height of each tile above the crown, and whether it can hold a cap
- Access for sweeping: which part lifts off and how it refastens
- Which appliance each flue serves, confirmed before a cap is chosen
- Anything near the chimney on the roof that belongs to a roofer
Cap questions we hear in Garden City
Can you tell me which cap I need over the phone?
Not reliably. Tile size, tile height and crown condition decide the cap, and those are measured on the roof. What you describe on the phone helps us bring the right ladder and sizing kit.
Will you need to get inside the house?
Not for the roof work itself, as long as we can reach the roof safely. If the flue needs clearing from below, or an animal is involved, someone needs to let us in to the fireplace.
More services in Garden City
-
-
-
-
-
-
Learn more about chimney cap installation and replacementAll services in Garden City
Replace a missing or rusted cap in Garden City
A cap that fits is ordered to the flue tile, so the first visit in Garden City is for measuring. Book it at (904) 920-5495.
Free Inspection