Local gas fireplace installation for Fruit Cove homes

A gas fireplace for a room in Fruit Cove with no chimney, venting through the wall where a free inspection shows the clearances allow.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Gas fireplace install specialists for Fruit Cove

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

We hand over the manual and show you the controls before we leave.

Family owned and operatedOne family business frames, vents and starts up the unit in Fruit Cove, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

How long a gas installation takes

Setting the unit in its framing is one of the shorter steps in the job. The calendar goes to the steps around it: the unit and vent parts arriving, framing the enclosure, running the vent, the gas contractor's line and any outlet, the inspection while the walls are open, and the finish. A wall exit is quicker to build than a roof exit, which adds attic work and roof covering. Your Fruit Cove schedule shows the steps in order with who does each, so you know when the room is out of use and when it comes back. Picked a room for a gas fireplace in Fruit Cove? (904) 920-5495 is the number for a free planning visit.

The county for Fruit Cove is St. Johns County. The 2020 Census counted 32,143 residents in Fruit Cove.

What a gas fireplace installation covers in Fruit Cove

Termination kept clear of windows, soffits and the meter
Enclosure and header framed to the manual's drawing
Start-up readings and leak check at the valve
Permit and inspections for your Fruit Cove install scheduled

Call (904) 920-5495 Free Inspection

Vent out, frame, wire, start up

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

Mantels and facing on Fruit Cove installs

The metal face around a gas fireplace opening runs hot, and the manual controls what can cover it and how low a mantel can sit.

Your tile, stone and mantel choices for the Fruit Cove install are checked against the manual's chart before framing.

10% off any service booked within 72 hours of inspection

Settling on a model for a room in Fruit Cove takes time, and the 72 hours give you some.

Call (904) 920-5495 Free Inspection

Siding, standoffs and heat

Vinyl siding needs protection from a termination's heat, and vent makers supply a standoff or siding shield for it. The standoff holds the termination out from the siding so the cladding is not in contact with hot parts, and the kit instructions say how it is mounted and flashed into the wall.

On brick or stucco, the termination mounts to the wall surface with its own trim. The manuals also require the termination to sit flush with the wall surface rather than recessed into it, so exhaust can clear the wall. Stucco and brick still need the termination sealed to the wall as the kit shows.

Framing the enclosure and the header

Framing starts from the manual's drawing, which gives the width, height and depth of the enclosure and the header height above the unit. The header matters because the space above a gas fireplace gets hot, and the manual sets how high framing can come. Some units have drywall support tabs on their face, and the manuals point out that those tabs are for holding the drywall edge and never for carrying framing or a header.

We build the enclosure to the drawing, square and plumb, so the unit sits where the clearances assume it does. A header set too low means reframing, so it is measured twice.

Wiring before the wall is closed

Remote receiver, wall switch and blower wiring are run before the finish goes on, as the manuals ask, because running it afterward means cutting into the new wall. A millivolt wall switch needs its own low-voltage wire to the valve, sized and limited in length as the manual shows.

A blower or an electronic-ignition unit needs an outlet in the location the manual gives, added by an electrician. We rough in the low-voltage wiring during framing and confirm the outlet is in place before the drywall goes up. The wire runs are labeled at both ends for whoever services the unit later.

Unit, vent route and trades on paper

Service access panels left removable after the finish
Outlet for a blower or ignition, added by an electrician where needed
Every connection leak-checked with solution before handover
Barrier screen fitted and logs set to the placement diagram

Gas fireplace install questions from Fruit Cove

Do you run the gas line to the new fireplace?

No. The line to the unit's shutoff valve is a gas contractor's job, or the propane supplier's on a propane system. The estimate says who and when, and start-up follows once gas reaches the valve.

Does the 10% discount cover a gas fireplace installation?

It does, when you book the installation within 72 hours of the free inspection. The written estimate shows the 10% off as its own line.